Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 354

background image

3.2

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Job Done Examples

Example 1: Connect to the Front Port and Change Default Passwords

Set the
Passwords,
Step by Step

Step 1. Follow the SEL-2032 installation instructions listed in

Checkout on page 2.15

Step 2. Connect one end of the SEL C234A cable to the serial port on

your PC or terminal, and connect the other end to Port F on the
front panel of the SEL-2032.

Step 3. The default factory settings for Port F are: 2400 baud, 8 data

bits, 1 stop bit, and no parity. Set your PC or terminal
communication parameters to the same settings and set your
terminal emulation program to vt100 or vt52 emulation. Start a
connection.

Step 4. Press a carriage return,

<Enter>

, and verify that a “*” prompt

is returned. The “*” indicates that you are in Access Level 0.

Step 5. If you do not get an “*” with each carriage return, then

something is wrong with your connection. Terminate your
serial connection, check your cable connections and your
communications parameters, and restart your serial I/O
connection.

Step 6. When you receive the “*” prompt, you can type

HELP

<Enter>

for a description of the commands available at Access

Level 0.

shows a successful connection followed by

the

HELP

and

ID

commands.

*

HELP <Enter>

Commands available at current access level:

- ACCESS - Change access level to Access Level 1
- HELP - Provide information on available commands
- ID - Display SEL-2032 identification information
- QUIT - Change access level to Access Level 0

*ID
"FID=SEL-2032-R110-V0-D991222","FID=SLBT-2030-R101-V0-D980121","0DD5"
"COMMUNICATIONS PROCESSOR - S/N 98205023","0A73"

*

Figure 3.1

Commands Available

Step 7. To change passwords you need to move through Access Level 1

to Access Level 2. Type

ACC <Enter>

to go to Access Level

1. The SEL-2032 will respond with:

Password: ? ******

Step 8. The default factory password for Access Level 1 is OTTER, so

type

OTTER <Enter>

and the SEL-2032 will respond with the

Level 1 access notification and the “

*

>” prompt indicating that

you are in Access Level 1.

Table 3.1

Factory-Default Passwords for Access Levels 1, 2, and C

Access Level

Factory-Default Password

1

OTTER

2

TAIL

C

CLARKE

Courtesy of NationalSwitchgear.com

«
...
70
71
72
73
74
...
»

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Бренд: NEC Страницы: 6

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: STONEFLY Страницы: 48

X-Pedition 2000

Бренд: Enterasys Страницы: 86

Thin Client US310e

Бренд: NEC Страницы: 6

iTRON B 70.2040

Бренд: JUMO Страницы: 41

Бренд: WABCO Страницы: 29

Бренд: Commell Страницы: 36

KÜHLER H2O 920

Бренд: Antec Страницы: 6

IA611 Xplained Pro

Бренд: Knowles Страницы: 14

Бренд: Microcomputer Systems Страницы: 21

Бренд: Data Translation Страницы: 62

VAR-SOM-MX6 HEAT PLATE KIT

Бренд: Variscite Страницы: 3

Бренд: TERSUS Страницы: 7

1000 Con?guration guide

Бренд: Nortel Страницы: 108

Бренд: D-Link Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды