manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

3.7

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Job Done Examples

Example 2: Using the SEL-2032 as a Port Switch

Step 5. Use 

SET A

 to define a timed trigger condition in the form of 

(Thh:mm:ss) to send a date message, at a specific time once 
each day, to the relay connected to Port 1. Skip Step 5 if you are 
using an SEL-500 series, SEL-300 series, or SEL-400 series 
relay with an IRIG-B input connected to the SEL-2032.

This setting sequence uses the 

SET A

 command to set a 

message trigger and a message in Port 1 of the SEL-2032. This 
example sets the SEL-2032 to issue the date command to the 
relay attached to Port 1 once each day. Even though you supply 
IRIG-B time to the relays, if a relay is powered down for any 
reason, it may need this date information to establish the 
current year because the year is not supplied by IRIG-B. The 
date is retrieved from the SEL-2032 Global region and 
formatted in a message string that the relay will recognize.

The SEL-2032 maintains date and time information in the 
Global region. You can access this information using the 

VIEW

 command. Use the labels displayed by the 

VIEW

 

command when you define the date message sequence with the 

SET A

 command. For an interpretation of the labels shown in 

the 

VIEW

 screen and for a description of the Global region, 

see 

Global Region on page 6.4

.

To see the Global data format, type 

VIEW 1:GLOBAL 

<Enter>

 to display Global database information. Your screen 

should look like the example in 

Figure 3.5

.

*>>

VIEW 1:GLOBAL <Enter>

Port 1,  Data Region GLOBAL   Data

FID = FID=SEL-2032-R100-V0-Z000000-D20021222
STATUS = 0100h  CONFIG = 0CA0h  __YEAR = 1997  DAY_OF_YEAR = 304 (10/01)
MONTH = 10  DATE = 31  TIME = 14:12:03.598  
ELEMENTS = 04h,00h,00h,20h,FFh,FFh,00h
REMOTE_BIT_REG = 0000h  REMOTE_BITS = 00h  _YEARS = 97
_HOURS = 14  _MINS = 12  _SECS = 3  
CARD1_FID = FID=SEL-2711-R100-V0-D971031
CARD1_SERVICES =       64  CARD1_STATUS = 0021h  CARD1_CONFIG = 0001h
  CARD1_STEST_ERR = 0082h
CARD2_FID =
CARD2_SERVICES =        0  CARD2_STATUS = 0000h  CARD2_CONFIG = 0000h
  CARD2_STEST_ERR = 0000h  PORT_STATUS = 0004h  ALT_PORT = 255
NUM_MESGS = 20  BAD_MESGS = 0

*>>

Figure 3.5

Global Data Region Contents

Now, type 

SET A 1

 to define a timed trigger condition and a 

message to send the date message to the relay connected to 
Port 1 at a specific time once each day. Enter the information 
and follow the prompts to set the SEL-2032 to match the 
settings shown in 

Table 3.4

.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Intel F-Tile SDI II Intel Agilex User Manual preview
F-Tile SDI II Intel Agilex
Бренд: Intel Страницы: 39
Aaeon SBC-555 Manual preview
SBC-555
Бренд: Aaeon Страницы: 72
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Бренд: IEI Technology Страницы: 136
Lanner ECA-4027 User Manual preview
ECA-4027
Бренд: Lanner Страницы: 99
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Бренд: Genexis Страницы: 7
Primera DUP-11 User Manual preview
DUP-11
Бренд: Primera Страницы: 82
WatchNet ENM-04 POE Quick Connection Manual preview
ENM-04 POE
Бренд: WatchNet Страницы: 2
Epson 6200A Core Cpu Manual preview
6200A
Бренд: Epson Страницы: 97
Epson 0C88832 Technical Manual preview
0C88832
Бренд: Epson Страницы: 159
Epson ARM720T Core cpu Core Cpu Manual preview
ARM720T Core cpu
Бренд: Epson Страницы: 224
Epson B80818 Series Installation Manual preview
B80818 Series
Бренд: Epson Страницы: 23
ASROCK iBOX-155 Quick Installation Manual preview
iBOX-155
Бренд: ASROCK Страницы: 2
Crestron Zum ZUMMESH-NETBRIDGE Quick Start preview
Zum ZUMMESH-NETBRIDGE
Бренд: Crestron Страницы: 2
Icom CT-M500 User Manual preview
CT-M500
Бренд: Icom Страницы: 7
ABB COM600 series 5.1 User Manual preview
COM600 series 5.1
Бренд: ABB Страницы: 42
Aaeon UP Xtreme i12 Edge Installation Manual preview
UP Xtreme i12 Edge
Бренд: Aaeon Страницы: 11
Aaeon NIM-S13D Quick Installation Manual preview
NIM-S13D
Бренд: Aaeon Страницы: 23
R.V.R. Elettronica SCM6/1 User Manual preview
SCM6/1
Бренд: R.V.R. Elettronica Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды