manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

3.4

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Job Done Examples

Example 2: Using the SEL-2032 as a Port Switch

Example 2: Using the SEL-2032 as a Port Switch

Introduction

This example assumes your substation has an SEL-2032, seven SEL-251 
Relays, an IRIG-B source, and a telephone line. Also, you have SEL-C239 
cables of the appropriate length to connect the SEL-2032 to each relay. You 
have a PC or terminal and an SEL C234A cable to communicate with the 
SEL-2032. You will connect all of these as shown in 

Figure 3.4

.

Figure 3.4

SEL-2032 Configured With SEL-251 Relays, External Modem, 

and IRIG-B Source

Identifying
the Problem

Your objective in Example 2 is to accomplish the following tasks:

➤

You want the SEL-2032 to time synchronize all IEDs with the 
IRIG-B source.

➤

You want to send date messages to the relays even though they 
receive IRIG-B time code, so if power is cycled on a relay, the 
appropriate date (including year) is available as a reference.

➤

You want to access information in all the IEDs through the 
telephone port.

Defining 
the Solution

Complete Hardware Connections

Step 1. Connect each SEL-251 as follows:

a. On the relay, install cable SEL-C239 connectors to 

Port 2R and AUX INPUT.

b. Plug the other end of cable SEL-C239 into the desired 

SEL-2032 serial port.

SEL-251

Relay

Time

Clock

SEL-251

Relay

SEL-251

Relay

SEL-251

Relay

SEL-251

Relay

SEL-251

Relay

SEL-251

Relay

Local

Terminal

IRIG-B

Input

Port 7

Port 6

Port 5

Port 4

Port 3

Port 2

Port 1

SEL-2032

Port F

Port 9

Aux.

Input

Aux.

Input

Aux.

Input

Aux.

Input

Aux.

Input

Aux.

Input

Aux.

Input

Port 2R

Cable

SEL-C234A

Modem

Cable

SEL-C226

Port 2R

Port 2R

Port 2R

Port 2R

Port 2R

Port 2R

All relay

cables

SEL-C239

Telephone 

Line

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Бренд: Tandberg Data Страницы: 2
Q-See QC814 Specifications preview
QC814
Бренд: Q-See Страницы: 2
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Бренд: Ruckus Wireless Страницы: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Бренд: Renesas Страницы: 6
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Бренд: Compaq Страницы: 4
Roland Super Sound Set SR-JV80-07 Owner'S Manual preview
Super Sound Set SR-JV80-07
Бренд: Roland Страницы: 8
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Бренд: Schrack Technik Страницы: 2
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Бренд: A2B Electronics Страницы: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Бренд: ZALMAN Страницы: 6
Uniden Data 2000 Manual preview
Data 2000
Бренд: Uniden Страницы: 5
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Бренд: Moxa Technologies Страницы: 36
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Бренд: Element14 Страницы: 2
Hauppauge WinTV USB Installation And Reference Manual preview
WinTV USB
Бренд: Hauppauge Страницы: 55
ENERMAX LIQMAX III ELC-LMT120-ARGB User Manual preview
LIQMAX III ELC-LMT120-ARGB
Бренд: ENERMAX Страницы: 32
ZALMAN ZM-GWB3 User Manual preview
ZM-GWB3
Бренд: ZALMAN Страницы: 9
Meridian Meridian 1 Option 11C Mini Technical Reference Manual preview
Meridian 1 Option 11C Mini
Бренд: Meridian Страницы: 546
SeaLevel SIO-485.LPCI User Manual preview
SIO-485.LPCI
Бренд: SeaLevel Страницы: 19
Dvico FusionHDTV 5 GOLD User Manual preview
FusionHDTV 5 GOLD
Бренд: Dvico Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды