manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

3.12

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Job Done Examples

Example 2: Using the SEL-2032 as a Port Switch

V(56)   =B*E*F
W(56)   =C*E*F
X(56)   =
Y(56)   =
Z(56)   =
A3(1346)=79CY
A4(2346)=
TR(1246)=50H+51T+51NT+V
RC(1246)=50H+TF
ER(1246)=51P+51QP+51NP+TF+W
SEQ(1)  =
ETC(1)  =
ITC(1)  =

Global settings
DEMR =Y       CFT  =60     TDUR =4      TFT  =30     TGR  =180 ITT  =5   TIME1=15
TIME2=0       AUTO =2      RINGS=3      IN1  =SS1    IN2  =DT  IN3  =RE  IN4  =
IN5  =52A     IN6  =     

=>

Figure 3.9

Relay Group 1 Settings

While you have the relay global settings on the screen, verify 
that:

TIME2 = 0
AUTO = 2 or 3  (setting 2 is for Port 2 and setting 3 is for 
both Ports 1 and 2)

These settings allow the SEL-2032 to continue to receive 
automatic messages from the relay without the port timing out. 
If these two settings are not as shown above, go to Access 
Level 2 and use the relay 

SET

 command to change them.

Quit transparent communication using the default disconnect 
sequence or keystroke 

<Ctrl+D>

.

NOTE

: After transparent 

communications with the relay, the 
SEL-2032 will reissue the STARTUP 
string to the relay to return it to the 
access level needed for proper 
operation. If you change a relay 
password, modify the port's startup 
string to match. If you use an SEL-501 
Relay and change one of the relay 
type settings, reconfigure afterwards 
so that the SEL-2032 maintains a 
correct target list.

You should see a termination message as shown in 

Figure 3.10

.

=>

<Ctrl+D>

Transparent Communications to Port 1 terminated

*>>

Figure 3.10

Terminate Transparent Communications

Step 4. Use the 

TOGGLE

 command, as shown in 

Figure 3.11

, to send 

the date message previously defined as MESG1 in the 
SEL-2032.

As shown here, you toggle the state of the D1 element to trigger 
the associated message MESG1. The SEL

OGIC®

 control 

equation in ISSUE1 normally does this, but the 

TOGGLE

 

command lets you test the process without waiting for the 
SEL

OGIC

 control equation condition to become true.

*>>

TOGGLE 1:D1 <Enter>

Bit toggled

*>>

Figure 3.11

TOGGLE Command Example

Reestablish transparent communications with the relay and 
verify that the date matches the date in the SEL-2032. Use the 

DATE

 command to change the date and year in the relay 

(DATE MM/DD/YY); exit transparent communication and 

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Paradyne 4300 Installation Instructions Manual preview
4300
Бренд: Paradyne Страницы: 22
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Бренд: Moxa Technologies Страницы: 19
Amplifier Tech ATP6700 Owner'S Manual preview
ATP6700
Бренд: Amplifier Tech Страницы: 36
Novus NVIP- NVRA0104/GO User Manual preview
NVIP- NVRA0104/GO
Бренд: Novus Страницы: 44
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Бренд: Lanner electronics Страницы: 59
H3C NSQ1GT48EA0 Manual preview
NSQ1GT48EA0
Бренд: H3C Страницы: 3
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Бренд: Balluff Страницы: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Бренд: MEMON Страницы: 2
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Бренд: ETL Страницы: 83
RANA Systems RanaSystems 13-0010--001 User Manual preview
RanaSystems 13-0010--001
Бренд: RANA Systems Страницы: 328
SYNTEK STA-UI-A0035 User Manual preview
STA-UI-A0035
Бренд: SYNTEK Страницы: 41
Kontron CP3002-RA User Manual preview
CP3002-RA
Бренд: Kontron Страницы: 98
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Бренд: PADAUK Страницы: 27
Intel BX80637I53570K Specification preview
BX80637I53570K
Бренд: Intel Страницы: 54
Stepper Motor Canada DB25-1205F Manual preview
DB25-1205F
Бренд: Stepper Motor Canada Страницы: 5
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Бренд: Cypress Semiconductor Страницы: 31
Teridian 71M6533 Quick Start Manual preview
71M6533
Бренд: Teridian Страницы: 2
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Бренд: XtendLan Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды