Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 73

Страница: 73 / 354

3.3

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Job Done Examples

Example 1: Connect to the Front Port and Change Default Passwords

Step 9. Type

2AC <Enter>

to go to Access Level 2; the SEL-2032

responds with the same password prompt.

The default factory password for Access Level 2 is TAIL, so
type

TAIL <Enter>

and the SEL-2032 responds with the Level

2 access notification and the “

>>” prompt indicating that you

are in Access Level 2.

Figure 3.2

demonstrates changing from Access Level 0 to

Access Level 2.

ACC <Enter>

Password: ? OTTER@

COMMUNICATIONS PROCESSOR - S/N 98205023 Date: 10/06/00 Time: 14:14:22

Level 1

*>2AC

Password: ? TAIL@@

COMMUNICATIONS PROCESSOR - S/N 98205023 Date: 10/06/00 Time: 14:14:45

Level 2

*>>

Figure 3.2

Changing Access Levels

Step 10. The

PAS

command is used to view and set passwords. Type

PAS <Enter>

to see the existing passwords settings.

Another form of the

PAS

command is used to set passwords.

The command

PAS 1

is used to change the Level 1 password.

For example,

PAS 1 <Enter>

starts the Access Level 1

password change sequence. Similarly, the command

PAS 2

starts the Access Level 2 password change sequence, and you
can use

PAS C

to change the Access Level C password.

Step 11. After entering your new passwords, use the

PAS

command to

view the new settings.

Figure 3.3

shows how to use the

PAS

command for viewing

and setting passwords. When setting your passwords, be sure to
choose “strong” passwords that cannot be guessed or broken
with an automated password cracker.

*>>

PAS <Enter>

1:OTTER
2:TAIL

*>>

PAS 1 <Enter>

New level 1 password: ?

******

Verify new level 1 password: ?

******

Level 1 password changed

*>>

PAS 2 <Enter>

New level 2 password: ? ******
Verify new level 2 password: ?

******

Level 2 password changed

*>>

PAS <Enter>

1:Ot3579
2:Ta2468

*>>

QUIT <Enter>

COMMUNICATIONS PROCESSOR - S/N 98205023 Date: 10/06/00 Time: 14:16:54

Figure 3.3

Using the PAS Command

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации

Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды