NXP Semiconductors LPC822M101JDH20 Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 487

NXP Semiconductors LPC822M101JDH20 Скачать руководство пользователя страница 321

UM10800

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2016. All rights reserved.

User manual

Rev. 1.2 — 5 October 2016

321 of 487

21.1 How to read this chapter

The ADC is available on all parts. The number of available ADC channels depends on the
package type.

21.2 Features

•

12-bit successive approximation analog to digital converter.

•

Input multiplexing among 12 pins.

•

Two configurable conversion sequences with independent triggers.

•

Optional automatic high/low threshold comparison and “zero crossing” detection.

•

Power-down mode and low-power operating mode.

•

Measurement range VREFN to VREFP (typically 3 V; not to exceed VDDA voltage
level).

•

12-bit conversion rate of up to 1.2 Msamples/s.

•

Burst conversion mode for single or multiple inputs.

•

DMA support.

•

Hardware calibration mode.

21.3 Basic configuration

Configure the ADC as follows:

•

Use the PDRUNCFG register to power the ADC. See

. Once the ADC is

powered by the PDRUNCFG register bit, the low-power mode bit in the ADC CTRL
register can be used to turn off the ADC when it is not sampling and turn on the ADC
automatically when any of the ADC conversion triggers are raised. See

and

•

Use the SYSAHBCLKCTRL register (

) to enable the clock to the ADC

register interface and the ADC clock.

•

The ADC block creates four interrupts with individual entries in the NVIC. See

.

•

The ADC analog inputs are enabled in the switch matrix block.See

.

•

The power to the ADC block is controlled by the PDRUNCFG register in the SYSCON
block. See

•

Calibration is required after every power-up or wake-up from Deep power-down
mode. See

Section 21.3.4 “Hardware self-calibration”

.

UM10800

Chapter 21: 12-bit Analog-to-Digital Converter (ADC)

Rev. 1.2 — 5 October 2016

User manual

Table 275. Pinout summary

Package

ADC channels available

TSSOP20

ADC_2, ADC_3, ADC_9, ADC_10, ADC_11

HVQFN33

ADC_0 to ADC_11

«
...
319
320
321
322
323
...
»

Содержание LPC822M101JDH20








































































































































































































































































































































































































































































































Отзывы:

Нет отзывов