NXP Semiconductors LPC2880 Скачать руководство пользователя

Страница: 131 / 362

UM10208_2

User manual

Rev. 02 — 1 June 2007

131 of 362

NXP Semiconductors

UM10208

Chapter 11: LPC2800 WDT

[1]

Reset Value reflects the data stored in used bits only. It does not include reserved bits content.

4.1 Watchdog Status Register (WDT_SR - 0x8000 2800)

The WDT_SR indicates whether the Timer Counter has matched the value in Match
Register 0.

Table 129. Watchdog register map

Name

Description

Access Reset

Value

[1]

Address

WDT_SR

Status Register.

Bits in this register can be set

when the Timer Counter matches MR0 or MR1
The bits can be cleared by writing to this register.

R/W

0x8000 2800

WDT_TCR

Timer Control Register.

Includes Enable and

Clear bits.

R/W

0x8000 2804

WDT_TC

Timer Counter.

The value of the Timer Counter

can be read from this register. For Watchdog
purposes this register should be regarded as
Read-Only.

R/W

0x8000 2808

WDT_PR

Prescale Register.

The WDT clock is divided by

the value in this register plus one, for
incrementing the Timer Counter.

R/W

0x8000 280C

WDT_MCR

Match Control Register.

Controls what happens

when the Timer Counter matches the Match
Registers.

R/W

0x8000 2814

WDT_MR0

Match Register 0.

An interrupt can be arranged

when the Timer Counter matches the value in
this register.

R/W

0x8000 2818

WDT_MR1

Match Register 1.

The LPC288x can be reset if

the Timer Counter matches the value in this
register.

R/W

0x8000 281C

WDT_EMR

External Match Control.

Enables the "m0" and

"m1" signals to the CGU and Event Router.

R/W

0x8000 283C

Table 130. Watchdog Status Register (WDT_SR - 0x8000 2800)

Bit

Function

Description

Reset
Value

MR0 Match

This bit can be set when the Timer Counter matches Match
Register 0. (An interrupt can be requested at this time.) Write a
1 to this bit to clear it.

MR1 Match

This bit can be set when the Timer Counter matches Match
Register 1. (If this event is enabled to reset the LPC288x, this
bit will never be read as 1.) Write a 1 to this bit to clear it.

31:2

Reserved, user software should not write ones to reserved bits.
The value read from a reserved bit is not defined.

Содержание LPC2880










































































































































































































































































































































































Результаты поиска

Содержание LPC2880

Отзывы:

Похожие инструкции для LPC2880

Бренды по названию

Популярные бренды

NXP Semiconductors LPC2880, Руководство пользователя

Результаты поиска

Содержание LPC2880

Отзывы:

Похожие инструкции для LPC2880

Бренды по названию

Популярные бренды