manualshive.com logo in svg

NXP Semiconductors LPC2880, Руководство пользователя

Пользовательская инструкция для микросхемы NXP Semiconductors LPC2880 доступна для загрузки бесплатно на нашем веб-сайте. Это подробное руководство поможет вам легко настроить и использовать продукт. Скачайте его сейчас с manualshive.com и начните эксплуатировать устройство без трудностей.

Поделиться
Скачать
background image

UM10208_2

© NXP B.V. 2007. All rights reserved.

User manual

Rev. 02 — 1 June 2007 

107 of 362

NXP Semiconductors

UM10208

Chapter 8: LPC2800 EMC

 

10.24 Static Memory Page Mode Read Delay Registers 

(EMCStaticwaitPage0-2 - 0x8000 8210,30,50)

The EMCStaticWaitPage0-2 Registers control how long the EMC waits before sampling 
read data, in subsequent accesses in an asynchronous page mode burst. These registers 
should only be modified during system initialization, or when there are no current or 
outstanding transactions. This can be ensured by waiting until the EMC is idle, and then 
entering low-power or disabled mode. This register is accessed with one wait state.

Table 8–102

 shows the EMCStaticWaitPage0-2 Registers.

 

10.25 Static Memory Write Delay Registers (EMCStaticWaitwr0-2 - 

0x8000 8214,34,54)

The EMCStaticWaitWr0-2 Registers control the delay from chip select to the write access. 
These registers should only be modified during system initialization, or when there are no 
current or outstanding transactions. This can be ensured by waiting until the EMC is idle, 
and then entering low-power or disabled mode. These registers are not used if the 
extended wait (EW) bit is 1 in the EMCStaticConfig Register. These registers are 
accessed with one wait state.

Table 8–103

 shows the EMCStaticWaitWr0-2 Registers.

Table 101. Static Memory Read Delay Registers (EMCStaticWaitRd0-2 - addresses 

0x8000 820C, 0x8000 822C, 0x8000 824C)

Bit

Symbol

Description

Reset 
Value

4:0

WAITRD

Static memory initialization code should write this field with one less 
than the number of AHB HCLK cycles that equals or just exceeds (the 
LPC288x max for clock to chip select assertion, plus the SDRAM max 
access time from chip select, plus the LPC288x min read data setup to 
clock). This field controls how long the EMC waits before sampling 
read data, in non-page mode read operations, and in the first access in 
an asynchronous page mode burst. The power-on reset value selects 
32 AHB HCLK cycles.

0x1F

31:5

-

Reserved, user software should not write ones to reserved bits. The 
value read from a reserved bit is not defined.

-

Table 102. Static Memory Page Mode Read Delay Registers 0-2 (EMCStaticWaitPage0-2 - 

addresses 0x8000 8210, 0x8000 8230, 0x8000 8250)

Bit

Symbol

Description

Reset 
Value

4:0

WAITPAGE

Static memory initialization code should write this field with one 
less than the number of AHB HCLK cycles that equals or just 
exceeds (the LPC288x max for clock to A[1:0] valid, plus the 
SDRAM max page mode access time from address, plus the 
LPC2800 min for data setup time to clock). This field controls how 
long the EMC waits before sampling read data, in subsequent 
accesses in an asynchronous page mode burst. The power-on 
reset value selects 32 AHB HCLK cycles.

0x1F

31:5

-

Reserved, user software should not write ones to reserved bits. 
The value read from a reserved bit is not defined.

-

Содержание LPC2880











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC2880

Hans Grohe iBox Hub 25020180 Assembly Instruction And Instructions For Use preview
iBox Hub 25020180
Бренд: Hans Grohe Страницы: 36
Uclear Motion Series User Manual preview
Motion Series
Бренд: Uclear Страницы: 40
Xilinx ML410 User Manual preview
ML410
Бренд: Xilinx Страницы: 101
Rare Waves Grendel 2TAC Manual preview
Grendel 2TAC
Бренд: Rare Waves Страницы: 18
ICS Tunnel Master Jr User Manual preview
Tunnel Master Jr
Бренд: ICS Страницы: 70
ZKTeco LockerPad-7B User Manual preview
LockerPad-7B
Бренд: ZKTeco Страницы: 27
Sunlight Supply TITAN CONTROLS KRONUS 2 Instruction Manual preview
TITAN CONTROLS KRONUS 2
Бренд: Sunlight Supply Страницы: 4
Eclipse TRILOGY T500 Series Instruction Manual preview
TRILOGY T500 Series
Бренд: Eclipse Страницы: 20
Window Master MotorController WCC 310 UL Installation Instructions Manual preview
MotorController WCC 310 UL
Бренд: Window Master Страницы: 39
Watlow Ramping and Profiling Microprocessor-Based Control SERIES 1500 User Manual preview
Ramping and Profiling Microprocessor-Based Control SERIES 1500
Бренд: Watlow Страницы: 90
ETI PFC 12 RS User And Service Manual preview
PFC 12 RS
Бренд: ETI Страницы: 14
WAGO 750-8202/040-000 Manual preview
750-8202/040-000
Бренд: WAGO Страницы: 418
Arbor Technology ELIT-1270 User Manual preview
ELIT-1270
Бренд: Arbor Technology Страницы: 79
Xylem McDonnel & Miller 157S-RBP-MD Instruction Manual preview
McDonnel & Miller 157S-RBP-MD
Бренд: Xylem Страницы: 8
Zamel RZB-04 Quick Manual preview
RZB-04
Бренд: Zamel Страницы: 2
EP Solar EPHC Series Instruction Manual preview
EPHC Series
Бренд: EP Solar Страницы: 3
Arbor Technology ARES-1231 Series User Manual preview
ARES-1231 Series
Бренд: Arbor Technology Страницы: 94
Belimo LMC230 Manual preview
LMC230
Бренд: Belimo Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды