![background image](http://html.mh-extra.com/html/nec/n8100-1668f/n8100-1668f_user-manual_251356099.webp)
Configuring Your Server 4-25
Option
Parameters
Description
Boot Monitoring
Policy
[Retry 3 Times]
Always Reset
Specify the processing when a timeout occurs during
boot monitoring. This option can only be specified if
[Boot Monitoring] is specified.
If [Retry 3 times] is selected, the system is reset after
the occurrence of a timeout and booting up the OS is
retried up to three times.
If [Always Reset] is selected, the system is reset
after the occurrence of a timeout and booting up the
OS is retried repeatedly.
Thermal Sensor
Disabled
[Enabled]
Specify whether to enable or disable the thermal
sensor monitoring function. If a thermal error is
detected with this item set to [Enabled], the system
stops at the end of POST.
Check previous
System Config
Disabled
[Enabled]
If the system configuration has been changed since
the previous startup, the system waits for user
intervention before booting the system.
BMC IRQ
[IRQ 11]
Disabled
Determines routing of the BMC interrupt.
Post Error Pause
Disabled
[Enabled]
Specify whether to stop the POST once at the end of
POST if an error occurs during the POST.
Memory Error
Halt
[Boot]
Specify whether to stop operation once at the end of
POST processing if there is a memory resource error
while executing POST processing. This setting is
effective if [POST Error Pause], which is on the
[Server] menu, is set to [Enabled].
Even if this option is set to [Boot], operation stops at
the end of POST processing if errors occurred for all
resources.
Power Switch
Inhibit
[Disabled]
Enabled
Specify whether to enable or disable the power
switch.
Note that it is not possible to disable the ability to
forcibly turn off the power by holding down the switch
for four seconds.
AC-LINK
Stay Off
[Last State]
Power On
Specify the state of power when the AC power to the
server is turn off once and then on.
Power ON Delay
Time (Sec)
[20] - 255
Specify the power on delay time within the range
between 20 and 255 seconds. The time specified is
valid when "Power On" or "Last State" is specified for
AC LINK.
Platform Event
Filtering
Disabled
[Enabled]
Specify whether to enable or disable the platform
event filtering (PEF) feature.
CLI SETUP
[Disabled]
Enabled
Set to [Enabled] to run teh CLI SETUP (Command
Line Interface SETUP Menu) instead of SETUP
menu of this GUI. To use the SETUP menu of this
GUI, set this item to [Disabled] on CLI SETUP menu.
[ ]: Factory-set
Содержание N8100-1668F
