Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 67 / 80

5.0 Operation

5.3.4.1 System Fault Messages

These fault messages are usually caused by some external issue that directly

affects the inverter/charger system.

Low Battery

– The inverter has turned off to prevent the batteries from

being over-discharged. The fault message displays and the FAULT (red) LED

illuminates when the battery voltage drops below the SETUP menu’s

02B

LBCO

setting for more than one minute. The inverter will automatically restart

and resume operation when the battery voltage rises to

≥

12.5 VDC (12-volt

models),

≥

25.0 VDC (24-volt models), or

≥

50.0 VDC (48-volt models).

Remedy:

This fault will also automatically restart if AC power

such as utility power or a generator is connected to the inverter/

charger’s input and battery charging begins.

High Battery

– The inverter has turned off because the battery voltage

is at a very high level. This fault message displays and the FAULT (red) LED

turns on when the battery voltage is above the High Battery Cut-Out (HBCO)

value. This fault will automatically restart and resume operation when the

battery voltage drops 0.3 VDC (12-volt models), 0.6 VDC (24-volt models),

or 1.2 VDC (48-volt models) below the HBCO value.

Info:

The HBCO value is dependent on your inverter revision

and model. Normally, the HBCO value for the ME/MM/RD Series

inverters is 16 VDC (12-volt models) or 32 VDC (24-volt mod-

els); and, the HBCO value for the MS/MMS Series inverters is

17 VDC (12-volt models), 34 VDC (24-volt models), or 68 VDC

(48-volt models).

Remedy:

This fault usually only occurs when an external DC

charging source is charging the inverter’s battery bank. Turn

off any other additional charging source to allow the DC voltage

level to drop.

•

Low Battery

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green) and INV

(green) LEDs are off.

FAULT

PWR

CHG

INV

Low Battery

Settings/Info...

Figure 5-18, Low Battery Fault

High Battery

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green), and INV

(green) LEDs are off.

Figure 5-19, High Battery Fault

FAULT

PWR

CHG

INV

High Battery

Settings/Info...

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды