Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 78 / 80

7.0 Warranty and Service Info

7.1 Limited Warranty

Magnum Energy, Inc., warrants the ME-RTR to be free from defects in material

and workmanship that result in product failure during normal usage, according

to the following terms and conditions:

1. The limited warranty for this product extends for a maximum of 12 months

from the product’s original date of purchase.
2. The limited warranty extends to the original purchaser of the product and

is not assignable or transferable to any subsequent purchaser.
3. During the limited warranty period, Magnum Energy will repair, or replace

at Magnum Energy’s option, any defective parts, or any parts that will not

properly operate for their intended use with factory new or remanufactured

replacement items if such repair or replacement is needed because of product

malfunction or failure during normal usage. The limited warranty does not

cover defects in appearance, cosmetic, decorative or structural parts or any

non-operative parts. Magnum Energy’s limit of liability under the limited

warranty shall be the actual cash value of the product at the time the original

purchaser returns the product for repair, determined by the price paid by the

original purchaser. Magnum Energy shall not be liable for any other losses

or damages.
4. Upon request from Magnum Energy, the original purchaser must prove the

product’s original date of purchase by a dated bill of sale, itemized receipt.
5. The original purchaser shall return the product prepaid to Magnum Energy

in Everett, WA. After the completion of service under this limited warranty,

Magnum Energy will return the product prepaid to the original purchaser via a

Magnum-selected non-expedited surface freight within the contiguous United

States and Canada; this excludes Alaska and Hawaii.
6. If Magnum repairs or replaces a product, its warranty continues for the

remaining portion of the original warranty period or 90 days from the date

of the return shipment to the original purchaser, whichever is greater. All

replaced products and parts removed from repaired products become the

property of Magnum Energy.
7. This limited warranty is voided if:

the product has been modi

ed without authorization

the serial number (if serialized) has been altered or removed
the product has been damaged through abuse, neglect, accident, high

voltage or corrosion
the product was not installed and operated according to the owner’s

manual

BEFORE RETURNING ANY UNIT, CONTACT MAGNUM ENERGY FOR A RETURN

MATERIAL AUTHORIZATION (RMA) NUMBER.

•
•
•

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды