Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 61 / 80

5.0 Operation

There are three operating modes of the inverter/charger system:
• Inverter Mode • Charger Mode • Fault Mode

5.3.1 Inverter Mode Messages

The inverter/charger will be in Inverter mode when AC power (utility or

generator) is not available, or unacceptable to the inverter/charger’s input.

The Inverter mode messages are

Off

Searching

Inverting

, and

Inverter

Standby

Off

- This message tells you that there is no AC available on the inverter’s

AC output. The inverter function is OFF and there is no utility or generator AC

power sensed on its input.

Searching

- The inverter is in Search mode. This means the AC loads

on the inverter output are less than the SETUP menu’s

02A Search Watts

setting. The Search mode function is used to reduce the inverter draw from

the battery, and may be turned off at any time if you want full inverter output

voltage available at all times (see the 02 Invert Setup section on page 26).

Inverting

- The inverter is providing AC voltage on its output by

inverting power from the batteries.

•

FAULT

PWR

CHG

INV

Off

Settings/Info...

Off

appears on the LCD. All LEDs

are off.

Figure 5-2, Off Mode

FAULT

PWR

CHG

INV

Searching

Settings/Info...

Figure 5-3, Searching Mode

Searching

appears on the LCD. The

PWR (green) LED is on solid and the

INV (green) LED slowly

ashes. The

FAULT (red) and CHG (green) LEDs

are off.

FAULT

PWR

CHG

INV

Inverting

Settings/Info...

Inverting

appears on the LCD. The

PWR (green) and INV (green) LEDs

are on solid. The FAULT (red) and

CHG LEDs are off.

Figure 5-4, Inverting Mode

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды