Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 77 / 80

6.0 Troubleshooting

6.2 Performing an Inverter Reset

Press and hold the Power ON/OFF button (see Figure 6-1) for approximately

fteen (15) seconds until the Charging/Inverting Status LED comes on and

ashes rapidly. Once the rapid

ashing has begun, release the Power ON/

OFF button. The Status LED will go off after the button is released.
After the inverter reset is completed, press the Power ON/OFF button to turn

the inverter ON.
Some older inverter models do not allow an inverter reset. If the inverter reset

fails you will need to power-down the inverter using the procedure below. In

either case, if an internal fault does not clear the inverter will require repair

at an authorized service facility.

Info:

The Power ON/OFF button is a small momentary type

switch which operates by lightly pressing and releasing.

Info:

All adjustable inverter/charger settings in the router

(except Setup

01B Contrast

01C Backlight

, and

03 Gen Control

- which revert back to default) are saved in non-volatile memory

and are preserved until changed - even if an inverter reset is

performed or if all power to the router or inverter is removed.

1. Press and hold the Power

ON/OFF pushbutton for 15

seconds.
2. Watch the Charging/

Inverting Status LED, after

approximately 15 seconds it

should come on and flash

rapidly to indicate the inverter

has reset. The Status LED will

go off after the pushbutton is

released .

Figure 6-1, Performing an Inverter Reset

6.3 Powering Down the Inverter

To power-down the inverter:

Remove all AC power (utility or generator power) to the inverter.
Open all the inverter DC disconnects (or disconnect the positive bat-

tery cable to the inverter).
Ensure all inverters and the router are disconnected from all AC and

DC power (the router display will be blank).
After the inverters have been disconnected from all power for 30

seconds, reconnect the inverter DC disconnects (or reconnect the

positive battery cable) and resume operation.

Info:

If DC disconnects are not used, there may be a momen-

tary spark when the positive battery cable is connected to the

inverter’s terminal. This is normal and indicates that the inverter’s

internal capacitors are being charged.

1.
2.

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды