Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 66 / 80

5.0 Operation

5.3.3 AC In Control Status Messages

These displays alternate with the inverter/charger status to indicate that

there is AC power present at the AC input, but the inverter/charger is not

connecting to the incoming power.

VDC Connect

- The DC battery voltage needs to fall below the

Set

Connect Volts

setting in the

02D AC IN VDC

menu in order for the inverter/

charger to reconnect to incoming AC.

Time Connect

- The time of day needs to fall within the

Set Connect

Time

setting per the

02C AC In - Time

menu in order for the inverter/charger

to reconnect to incoming AC.

AC In - Disabled

- The inverter/charger is being prevented from

reconnecting to any incoming AC.

5.3.4 Fault Mode Messages

The FAULT LED comes on and a fault status is displayed when an abnormal
condition is detected. Use the information in this section to determine and
correct the issue.

Info:

Many of the faults will automatically restart when the fault

is cleared. Some will require a manual restart. This requires

the ON/OFF INVERTER button on the router to be pressed and

released. Finally, if the fault will not clear, an inverter reset may

be required – see Section 6.2 to perform an inverter reset.

•

FAULT

PWR

CHG

INV

VDC Connect

Settings/Info...

VDC Connect

appears on LCD. PWR

(green) is on solid and CHG (green)

is blinking.

Figure 5-15, VDC Connect Mode

Time Connect

appears on LCD. PWR

(green) is on solid and CHG (green)

is blinking.

FAULT

PWR

CHG

INV

Time Connect

Settings/Info...

Figure 5-16, Time Connect Mode

FAULT

PWR

CHG

INV

AC In - Disabled

Settings/Info...

AC In - Disabled

appears on LCD.

PWR (green) is on solid and CHG

(green) is blinking.

Figure 5-17, AC In - Disabled Mode

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды