Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 72 / 80

5.0 Operation

StackPhase Fault

appears on the

LCD and the FAULT (red) LED is on.

The PWR (green), CHG (green), and

INV (green) LEDs are off.

FAULT

PWR

CHG

INV

StackPhase Fault

Settings/Info...

Figure 5-32, StackPhase Fault

StackPhase Fault -

1. The AC input wiring is incorrect; or, 2. One

phase was lost from the AC input source; or, 3. One of the inverter’s internal

transfer relays is bad; or, 4. The inverter’s AC input circuit breaker may be

open.

Remedy:

If this fault doesn’t clear after checking these four

recommendations, perform an inverter reset (Section 6.2).

5.3.4.3 Internal Fault Messages

The inverter continually monitors several internal components. If a condition

inside the inverter occurs that does not allow proper operation, the inverter

shuts down to protect itself. To clear these “internal” faults, the inverter will

require an inverter reset.

Remedy:

Perform an inverter reset (see Section 6-2). After

resetting the inverter, press the ON/OFF INVERTER button to turn

the inverter on and verify the fault has cleared. If the internal

fault remains, the inverter will require repair at an authorized

service facility.

Internal Bridge

- This fault message displays and the inverter shuts down

because the internal power-bridge protection circuit has been activated.

Internal Charger

- This fault message displays and the inverter shuts

down because the internal charger protection circuit has been activated.

•

FAULT

PWR

CHG

INV

Internal Bridge

Settings/Info...

Internal Bridge

appears on the LCD

and the FAULT (red) LED is on. The

PWR (green), CHG (green), and INV

(green) LEDs are off.

Figure 5-33, Internal Bridge Fault

FAULT

PWR

CHG

INV

Internal Charger

Settings/Info...

Internal Charger

appears on the

LCD and the FAULT (red) LED is on.

The PWR (green), CHG (green), and

INV (green) LEDs are off.

Figure 5-34, Internal Charger Fault

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды