Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 75 / 80

6.0 Troubleshooting

The router may not be functioning correctly, use the following table to help

nd solutions.

Table 6-1, Router Control Troubleshooting Guide

Symptom

Possible Cause

Solution

Display shows

unrecognizable

letters or

symbols.

Static electricity

may have been

discharged into the

LCD display.

Refresh Display

: Press and

hold the SELECT button for 10

seconds.

LCD text

display is

locked-up,

pressing any

button has

no response

- may show

“

revision

” or

“

connecting

”.

RJ11 connections on

communication cable

are not making a

good connection.

Reset router

: 1) Disconnect

router cable from inverter for

5 seconds and reconnect; 2)

Check RJ11 cable connection on

back of router (see Figure 2-3).

Important: Ensure the RJ11

connector is pushed into the

correct port. You should feel/

hear “click” when the connection

is made.

Router not getting

suf

cient power from

inverter.

Ensure inverter batteries are

connected and inverter is

operating correctly. Inverter

should be able to invert and

power AC loads from batteries

(ensure no AC power is

connected to the inverter AC

inputs).

LEDs and

backlight are

off.

Router is in Power

Save mode.

Press any button to reactivate

router (or turn Power Save

mode to

Off

Router is non-

functional

(no lights, no

text on LCD

display, and no

response when

pressing any

button).

Communication

cable bad or not

correctly connected

to router port on

inverter.

Check communications cable

from inverter to router, ensure:

1) It is connected to the

Router port, 2) The correct

communications cable is used

(a 4-conductor telephone

cable may be substituted to

determine if cable is good).

Inverter is not

connected to

batteries.

Ensure inverter batteries are

connected and inverter is

operating correctly without

any AC power connected (can

invert and power AC loads from

batteries).

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды