Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 13 / 80

2.0 Installation

2.6 Connecting the Communication Cables

To connect the communication cables:

Connect a communication cable to the Remote port on every inverter

installed in parallel (see Figure 2-5), using the supplied remote cables.
Route the inverter-connected communication cables from each inverter/

charger to your router. Follow the same route you used for the CAT 5

cables.
Connect each communication cable to its respective communication port

on the router. (P1-P6 for the appropriate number of inverters installed in

parallel.) Refer to Section 2.6.1 and Figures 2-7 through 2-9.
Connect any accessories to the remaining open communication ports

on the router.

Info:

It is recommended that the Master inverter be connected

to remote communication

Port 1

, Slave 1 to remote communi-

cation

Port 2

etc., in order to more easily keep track of which

inverter is displayed on each port.

Info:

It is recommended that all accessories be connected

directly to the router using any available communication ports

(P1-P6). Except for remotes (i.e., ME-RC or ME-ARC), if there

are additional accessories to connect, but all the router’s com-

munication ports are being used, the additional accessories may

be connected to the Network ports on the stacked inverter/char-

gers. Any accessory connected directly to the Network port on

an inverter/charger will display as an accessory on the router

port to which the inverter/charger is connected.

Example:

A ME-AGS-N connected to the Network port on the

master inverter (P1) will display as

P1Acc

on the router.

Info:

Multiple accessories of the same type may be connected

to the system, but there are some limitations to the number

of accessories. You may connect a maximum of one ME-RC or

ME-ARC remote, two ME-AGS-N modules, and any number of

ME-BMK/ME-BMK-NS accessories.

Info:

The ME-ARC or ME-RC remote must be connected directly

to the router and programmed to indicate which port the remote

is monitoring. It is recommended that the ME-RC or ME-ARC

is set to monitor “System” in most installations. The ME-RC

or ME-ARC must not be directly connected to the Remote or

Network ports on the MS -PAE inverter when the router is also

connected.

Info:

When used in conjunction with a router, a ME-RC or ME-

ARC has limited functions. The remote control monitors the port

it is designated to display, turns all parallel inverter/chargers

on/off, and displays METER and TECH information. The ME-ARC

does not control the inverter/chargers via the CTRL button.

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды