Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 25 / 80

3.0 Setup

03 AGS Meters

03A AGS Status:

If there is no Automatic Generator Start (ME-AGS-N)

module connected, the status will read “

No Comm

”. If there is a ME-AGS-N

connected, please refer to the ME-AGS-N owners manual (PN: 64-0039)

for information on the status messages.

Info:

These menus allow the optional ME-AGS-N (Auto Gen Start

-Network version)

— if installed — to display the status of the

generator. Refer to the ME-AGS-N Owner’s Manual (PN: 64-0039)

for detailed information on the AGS and these menus.

03B DC Volts-AGS:

This menu displays the DC voltage measured at pins

3 and 4 of the ME-AGS-N module. This menu is useful in setting up the

voltage start for the AGS, and for troubleshooting its operation.

Info:

The DC voltage reading in this menu may vary from the

DC voltage readings in the

01A DC Volts

and

04C DC Volts-

BMK

menus. Each DC voltage reading is taken at a different

place in the system, and therefore there may be wire losses or

connections that make the readings differ. It is important when

troubleshooting the system to read the appropriate related meter

for each device. When troubleshooting the AGS, use the

03B DC

Volts-AGS

menu item for veri

cation and testing purposes.

03C Gen Run Time:

This menu displays the amount of time the

generator has been running since the AGS auto-started the generator.

This menu does not display run time when the generator has been

manually started.

Info:

This hour meter resets each time the generator is stopped.

This is useful when trying to determine how long the generator

has been running in

Auto

mode if you were not present when

it started. This meter does not replace the hour meter for total

hours the generator has run.

03D AGS Temp:

This menu displays the temperature of the AGS temp

sensor (included with ME-AGS-N, but use is optional), and is helpful in

determining proper placement and operation of the AGS temp sensor.

03E Since Gen Run:

This menu displays the number of days since the

generator has last run. This menu is useful in determining if the AGS

start and stop settings are set up correctly.

Info:

This meter resets whenever the generator is either auto-

started, exercised, or manually started. The meter reads the

B+/run signal provided by the generator to the AGS module.

04 BMK Meters

These menus display the status of the battery system from the optional
ME-BMK/ME-BMK-NS, if installed. Refer to the ME-BMK/ME-BMK-NS Owner’s

Manual (PN: 64-0013) for detailed information on the Battery Monitor Kit
and these menus.

04A BMK SOC:

This display is the best way to monitor the actual state

of the battery. The read only display shows the State of Charge (SOC)

for the connected battery bank. The SOC represents the condition of the

battery as a percentage of the available capacity left in the battery.

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды