Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 38 / 80

3.0 Setup

transfer time from Charge mode to Inverter mode is >16 milliseconds

when using these settings.

Dropout = UPS Mode

Use the

UPS Mode

setting when the AC source

is well regulated above 105 VAC (210 VAC for export inverter models)

and the inverter loads are sensitive to voltage

uctuations. This setting

is intolerant of voltage

uctuations and will provide a quick transfer. The

transfer time from Charge mode to Inverter mode is

≤

16 milliseconds

when using this setting. Do not use this setting if using a generator as

your AC source.

Info:

If you get nuisance AC disconnects, either change the

setting to 100 VAC or less (export inverter models: 200 VAC or

less), or obtain a better voltage regulated AC source.

03E Absorb Done (Time, Amps, SOC):

This setting determines whether

time, amps, or SOC are used to determine when the second stage of

battery charging, or Absorption Stage, is

nished and transitions to

the

nal charge stage (see

03G Final Charge Stage

). Absorption is the

second stage of the charge process and the batteries will be almost fully

charged.

Info:

If the Absorb stage is short or terminated, the batteries

may not receive a full charge. In contrast, if the Absorb stage

is too long the batteries may be overcharged. Either scenario

may lead to damage to the batteries. Contact your battery

manufacturer to ensure the best charge settings are used for

your type of batteries.

Set Absorb Done Time

Set Absorb Done Time

is used when a speci

c time

is determined to be the best solution for ending absorption time. When using

time, the battery bank size will typically determine the length of the absorb

time setting. Taking speci

c gravity readings of the batteries and adjusting

the absorb time may be needed in order to obtain the appropriate absorb time

for your battery type and battery bank size. The larger the battery bank the

longer the absorb time to ensure the batteries receive a full charge, or you

can use Table 3-2 to select the setting – as a general rule of thumb.

Default Setting

Absorb Done Time = 2.0 Hrs

Table 3-2, Battery Amp/Hrs Capacity to Suggested Absorb Time

•

Battery

AmpHrs

Capacity

Suggested

Absorb Time

Battery

AmpHrs

Capacity

Suggested

Absorb Time

200 to 300

60 minutes

1310 to 1500

240 minutes

310 to 500

90 minutes

1510 to 1700

270 minutes

510 to 700

120 minutes

1710 to 1900

300 minutes

710 to 900

150 minutes

1910 to 2100

330 minutes

910 to 1100

180 minutes

2110 to 2300

360 minutes

1110 to 1300

210 minutes

2310 to 2500

390 minutes

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды