Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 63 / 80

5.0 Operation

Absorb Charging

- The Absorb Charge state is the constant voltage

stage and begins when the absorb voltage is reached (determined by the

SETUP menu’s

03B Battery Type

setting) while Bulk charging. During this

stage, the DC charging current decreases in order to maintain the absorb

voltage setting. This charge stage continues until the

03E Absorb Done

(

Time

Amps

, or

SOC

) or

03F Max Charge Time

setting is reached.

•

FAULT

PWR

CHG

INV

Absorb Charging

Settings/Info...

Absorb Charging

appears on LCD.

PWR (green) is on solid. CHG (green)

LED is typically on solid, but may blink

slowly. FAULT (red) LED is off, and INV

(green) LED could be on or off.

Figure 5-8, Absorb Charging Mode

Float Charging

appears on LCD. PWR

(green) LED is on solid. CHG (green) LED

is typically on solid, but may blink slowly.

FAULT (red) LED is off, and INV (green)

LED could be on or off.

FAULT

PWR

CHG

INV

Float Charging

Settings/Info...

Figure 5-9, Float Charging Mode

Float Charging

- In Float Charging mode, the charger reduces the

charge voltage and tries to maintain the batteries at the

oat charge voltage

setting. This is determined by the SETUP menu’s

03B Battery Type

setting

as shown in Table 3-1.

Info:

If the battery voltage falls

≤

12.1 VDC (12-volt models),

≤

24.2 VDC (24-volt models) or

≤

48.4 VDC (48-volt models);

the unit will initiate bulk charging.

Full Charge

- This status indicates that you have entered the Battery

Saver™ mode. This mode maintains the batteries without overcharging,

and prevents excessive loss of water in

ooded batteries or drying out of

GEL/AGM batteries. After four hours of

oat charging, the charger will turn

off and

“Full Charge”

displays (charger is now in Battery Saver™ mode).

If the battery voltage drops to

≤

12.6 (12-volt models),

≤

25.2 (24-volt

models) or

≤

50.4 (48-volt models), the charger will automatically initiate

another 4 hours of

oat charging. This cycle helps to ensure the batteries are

maintained and continues as long as AC power is continuously connected to

the AC input. “

Full Charge

” only displays if

Multi-Stage

is selected from the

03G Final Charge Stage

menu.

•

FAULT

PWR

CHG

INV

Full Charge

Settings/Info...

Full Charge

appears on LCD. PWR

(green) LED is on solid. CHG (green)

LED blinks slowly. FAULT (red) LED

is off, and INV (green) LED could be

on or off.

Figure 5-10, Full Charge Mode

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды