Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 45 / 80

3.0 Setup

Info:

When the router is connected to inverters that are stacked

in parallel or series, there will be a stacking indication following

the model number. The indications will indicate the following

stacking conditions: “

PM”

- Parallel Master; “

PS”

- Parallel Slave;

“

SM”

- Series Master; “

SS”

- Series Slave.

Info:

The

BMK, AGS, and the remote accessories may display

a “

0.0

” revision for several reasons. Either the accessory is not

installed, there is no communication because of a bad or miswired

network cable, the device is not powered, or the device is bad.

Firmware Versions (TECH 03):

The

Firmware Versions (Acc Port)

displays all the accessories connected to the router. The accessory versions

display in the order of the port to which they are connected (1-6).

Fault History (TECH 04):

This menu shows a two screen display for each

history of the last 9 inverter faults. Information for each fault displays

from the most recent fault (H1) to the earliest fault (H2 up to H9).

Info:

All recorded fault history displays will be retained (except

for the day the fault occurred), even if power is removed from

the router.

Info:

All recorded fault history information can be cleared by

going to the Fault History front screen (display shows “Fault

History\Press Select to View\Tech 04”). Once this screen displays,

press and hold the SELECT knob for ~ 5 seconds until the screen

displays “No Faults Recorded\Tech 04”.

•

H1    Low Battery
BTS   25C Tfmr   45C
FETs  40C
P1 3 12 :00a Tech  04

Port

Days since fault

Time

Fault Mode

Transformer,

Battery , and FET

Temps

Fault History Number

H1 Low Battery
Inverting
21 .0Vdc 12Adc
P1 3 12 :00a Tech 04

Port

Days since fault

Time

Fault Mode

DC Battery Voltage

Status

DC Amps

Fault History Number

Figure 3-8, Fault History (fi rst and second screens)

Figure 3-8 - first screen (left graphic): The top line displays the fault history

number and the fault mode. The second line displays the status of the inverter/

charger at the time of the fault. The third line displays DC battery voltage

and amperage readings at the time of the fault. The bottom line displays the

port that the fault occurred at, how many days ago the fault occurred, the

time of the fault, and the menu in which it occurred.
Figure 3-8 - second screen (right graphic): The top line displays the fault

history number and the fault mode. The second and third line display

transformer, battery, and FETs temperatures at the time of the fault. The

bottom line displays the port that the fault occurred at, how many days ago

the fault occurred, the time of the fault, and the menu in which it occurred.

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды