Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 57 / 80

4.0 Menu Map

5.0 Operation

This section explains how to operate an inverter/charger using the router. It

also covers the operational statuses determined by the LED indicators and

the LCD display.

5.1 Front Panel

The router front panel contains LEDs and a LCD display for viewing system

status, pushbuttons to control system operation, and a rotary knob that

enables you to locate and select system information and settings.

Inverting

25.6 VDC 20 Amps

System Home

PORT, CTRL, METER, SETUP,

TECH Buttons

Rotary

SELECT Knob

LCD Display

LED

ON/OFF

LED Indicators

Figure 5-1, ME-RTR Front Panel Controls and Indicators

5.1.1 LED Indicators

There are four LED indicators on the front panel that light solid or blink to

indicate the inverter/charger’s status. When the router is

rst powered-up,

all the LED’s come on as it goes through a self-test. Once the self-test is

complete, the LEDs and the LCD provide the operating status of the inverter/

charger. See Section 5.3.4 for more information on the LED indicators.

5.1.2 LCD Display

The LCD display is used for setting up the system operation, as well as

viewing current operating status and fault conditions. This display has four

lines of alphanumeric characters and features a backlight that can be set to

turn off to conserve power. The top line provides the inverter/charger status,

which is detailed in this section. The second line displays battery information

while using the METER menu, displays system troubleshooting information

while in the TECH menu, and displays menu items that can be con

gured

for your speci

c system operation while in the SETUP menu. This display

automatically powers-up with the current system status on the top line and

the Home screen (detailing the inverter’s DC voltage and current as shown

in Figure 5-1) on the bottom line.

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды