Magnum Energy ME-RTR Скачать руководство пользователя страница 21

Страница: 21 / 80

3.0 Setup

02 CHG (Charge) Control

CHG Control

allows you to set the Charger mode to

Multi-Stage

Force

Float

, or to

Restart Bulk

. Most of the time the charger should be left in the

Multi-Stage

setting, but to override this setting use the CTRL button and the

CHG Control

menu. The charger can be forced into the Float mode or you

can start the Bulk mode using the

Force Float

Restart Bulk

settings from

the CTRL button’s

02 CHG Control

menu item.

Multi-Stage:

This charge pro

le starts in Bulk mode (maximum cur-

rent). It transitions to the Absorption stage (constant voltage). When

the Absorption voltage is reached (as determined by the SETUP menu’s

03E Absorb Done

setting), it

nally transitions to the

nal charge stage

as selected in the SETUP menu’s

03G Final Charge Stage

menu item.

Info: Multi-Stage

must be selected in order to use the

nal

charge stage selected in the

03G Final Charge Stage

menu.

Force Float:

This charge pro

le forces the charger to stay in the Float

mode as long as AC is present and the charger is active.

Force Float

most often used when another source of charging such as PV, wind, or

hydro is available to keep the batteries at or above the

oat voltage. If

AC is disconnected and then reconnected the charger will go directly to

the Float mode, and will not initiate a Bulk or Absorption charge cycle.

CAUTION:

Using the

Force Float

setting may not fully charge the

batteries. Most batteries require a Bulk and Absorption charge

cycle in order to fully recombine the electrolyte in the batteries

and bring the speci

c gravity to the proper level. Be sure to check

with your battery manufacturer before using this setting.

Info:

Silent

is selected from the

03G Final Charge Stage

menu,

you can override this selection with

Force Float

to temporarily

oat the batteries.

Restart Bulk:

This selection restarts the Bulk cycle from any stage in

the charge cycle. The

Restart Bulk

setting is useful when a full Multi-

Stage charge cycle does not bring the speci

c gravity of the batteries

to the proper level.

Info:

The

Restart Bulk

setting automatically defaults back to

the

Multi-Stage

setting once the inverter/charger status displays

“

Bulk Charging

”.

Info:

If you have to continually restart the Bulk cycle in order

to bring the batteries to full charge, check the settings from the

SETUP button’s

03 Charger Setup

menu items to make sure the

batteries are fully charged at the end of a regular Multi-Stage

charge cycle. Check with your battery manufacturer for proper

battery charger settings.

CAUTION:

Frequently restarting the Bulk cycle may result in

overcharging of the batteries.

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Бренды по названию

Популярные бренды