Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 36 / 80

3.0 Setup

Info:

The voltage settings shown in Table 3-1 are based on the

Battery Temperature Sensor (BTS) having been at a temperature

of 77° F (25° C), or not connected. If the BTS is connected, the

actual charge voltage will increase if the temperature around

the BTS is below 77° F (25° C), and decrease if higher than 77°

F (25° C). This ensures the batteries receive the correct charge

voltage regardless of temperature.

Table 3-1, Battery Type to Charge Voltages

Battery

Type

Inverter

Voltage

Absorption

Voltage

Float

Voltage

Equalization

Voltage

GEL

12 VDC

14.1 VDC

13.6 VDC

14.1 VDC

24 VDC

28.2 VDC

27.2 VDC

28.2 VDC

48 VDC

56.4 VDC

54.4 VDC

56.4 VDC

Flooded

12 VDC

14.6 VDC

13.4 VDC

15.5 VDC

24 VDC

29.2 VDC

26.8 VDC

31.0 VDC

48 VDC

58.4 VDC

53.6 VDC

62.0 VDC

AGM 1

12 VDC

14.3 VDC

13.1 VDC

15.5 VDC

24 VDC

28.6 VDC

26.2 VDC

31.0 VDC

48 VDC

57.2 VDC

52.4 VDC

62.0 VDC

AGM 2

12 VDC

14.5 VDC

13.5 VDC

14.5 VDC

24 VDC

29.0 VDC

27.0 VDC

29.0 VDC

48 VDC

58.0 VDC

54.0 VDC

58.0 VDC

Custom

12 VDC

12.0-16.0 VDC 12.0-16.0 VDC

12.0-16.0 VDC

24 VDC

24.0-32.0 VDC 24.0-32.0 VDC

24.0-32.0 VDC

48 VDC

48.0-64.0 VDC 48.0-64.0 VDC

48.0-64.0 VDC

Note 1: Voltage same as absorption voltage – to prevent equalization.

Note 2: Specifi cations for Concord (Lifeline Series) AGM batteries.

Note 3: Specifi cations for East Penn, Deka, Discover and Trojan AGM batteries.

Note 4: When using the Custom setting, the EQ (Equalization) voltage

adjustment cannot be set lower than the Absorb Voltage setting. Also, the

EQ Voltage adjustment cannot be set higher than 2-volts (12-volt systems),

4-volts (24-volt systems), or 8-volts (48-volt systems) above the Absorb

voltage setting.

03C Max Charge Rate:

Sets the maximum charge rate allowed to

charge the batteries during Bulk, Absorption, Float, and Equalize

charging. Selections are

Max Charge = 0%

up to

Max Charge = 100%

The

Max Charge = 0%

setting is available to help minimize charging

while continuing to allow pass-through power. The rest of the selections

are provided to limit the charge rate to the battery bank, which helps

prevent battery overheating caused by charging at too high a charge rate.
The maximum charge selections are provided as a percentage of the

inverter/charger’s maximum charging capability. Refer to the label on

the side of the inverter or the owner’s manual for the inverter/charger

to determine its maximum charge rate. Once you

nd this maximum

charge rate, determine the percentage needed to limit the charge rate

to your battery bank.

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды