background image

IQ422, IQ4NC/00, IQ4NC/12 Controllers Installation Instructions - Confi guring TG201265 Issue 12, 24-Jul-2018  

 1

InstallationInstructions-Configuring

IQ422, IQ4NC/00, IQ4NC/12

Controllers

Important: Retain these instructions

These instructions shall be used by trained service 

personnel only. 

If the equipment is used in a manner not 

specifi ed by these instructions, the protection provided by the 

equipment may be impaired.

https://partners.trendcontrols.com

 

 1

Isolate All Power 

(including any I/O supplies)

BEFORE STARTING CONFIGURATION

CONTENTS

Before Starting Confi guration .......................................

1

Confi guration .................................................................

1

Connect to IQ4xx

 ........................................................

10

Reset to Defaults

 .........................................................

12

2 CONFIGURATION

Read&AgreetoEndUserLicenceAgreement

Additional Documentation Required

 

SET Manual (TE200147)

 

IP Tool Manual (TE200638)

 

IQTool Monitor Applet Manual (TE201298)

 

IQTool Addresser Applet Manual (TE201299)

 

IQ4 Confi guration Manual (TE201263)

Note: PDF copies are included with SET installation in the 

following folder: C:\...\Trend Control Systems\Documentation

IQ422, IQ4NC/00, IQ4NC/12 Installation 

Instructions - Mounting (TG201264)

SET Manual (TE200147)

Prepare Ethernet Network 

(if using Ethernet)

Install DHCP Server

If the IP address settings (IP address, subnet mask, default 

router, WINS and DNS servers’ addresses) are to be supplied 

by a DHCP server, ensure one is installed on the Ethernet 

segment  to  which  the  IQ422,  IQ4NC/00,  IQ4NC/12  is 

connected.

Install WINS Server

If  host  names  are  being  used  for  IP  addressing  across  a 

router, a WINS server must be installed.

Install DNS Server

If email alarms are being sent, and the email server address 

is identifi ed by internet domain name, a DNS server must be  

installed.

IQ422, IQ4NC/00, IQ4NC/12 Installation 

Instructions - Mounting (TG201264)

PSU

PSU

O

I

O

I

O

I

Install the IQ422, IQ4NC/00, IQ4NC/12

InstallSETonPC/Laptop

WARNING 

Connecting  leads  may  be  connected 

to power supplies. Isolate before touching.

Summary of Contents for IQ422













Reviews: