Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 26 / 80

3.0 Setup

Range is

100%

, where 100% represents a fully charged battery

and 0% means the battery is completely discharged.
If no % displays, there are 3 status menus to determine what state the
BMK is in:

Pwr-up Fault

- The battery monitor faulted when it was powered-up.

The fault occurred because the power-up self-test failed.

No Comm

- This indicates the ME-BMK/ME-BMK-NS is not communicating

with the router. The most common causes are: no ME-BMK/ME-BMK-NS
installed in the system, a bad network cable, or no power to the ME-
BMK/ME-BMK-NS.

Think’n

- The battery monitor is connected and actively monitoring the

battery system. The router displays “

Think’n

” (or “

n’k“

in some screen

displays) to indicate that the SOC reference point is being calculated.
After the batteries are fully charged, the display changes from “

Think’n

”

to “

100%

” and begins to provide accurate SOC percentage values.

04B DC Volts - BMK:

This meter displays the real-time battery voltage

from

07.00

70.00 volts

(± 0.02 volts).

04C DC Amps - BMK:

This meter displays the real-time charge current

(amps into the battery), or the discharge current (amps out of the

battery). Charging is shown as a positive (+) number and discharging is

shown as a negative (-) number. The range is from

±0.1

999 amps

with a 1.0% accuracy.

04D AH In/Out:

This meter displays the amp-hours returned to or

removed from the battery. When this value is positive, it represents

amp-hours returned to the battery during any subsequent charging. A

negative value represents amp-hours removed from a full battery. Its

range is

±32768 AH

O4E Resettable AHrs:

This meter displays the total amp-hours

removed from the battery since it was last reset. This display can be

used as a battery load indicator to help determine and monitor the

battery load consumption. Its range is

6,553.50 amp-hours

(0.1

amp hour resolution).

04F Total kAHrs Out

(

Total Amp-Hours Removed):

This meter

displays the total amp-hours removed from the battery since the Sense

Module was

rst connected. This display can be used as a battery

service life indicator. The value is displayed in 0.1k [or 100 amp-hours

(“k” equals 1000)] resolution up to a maximum of 6,553.5k amp-hours

(6,553,500 amp-hours). The displayed number resets to 0.0k when the

Sense Module is disconnected from power.

04G Minimum VDC:

This menu displays the lowest battery voltage

since the last reset. The voltage shown on the display is averaged each

second and is helpful when troubleshooting or detecting an over-discharge

condition.

04H Maximum VDC:

This menu displays the highest battery voltage

since the last reset. The voltage shown on the display is averaged each

second, this allows you to check your charging system (battery charger,

charge controller, etc.) to ensure the charging voltage has been attained.

This display is also helpful when troubleshooting or detecting if an over-

charge condition has occurred.

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды