Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 60 / 80

5.0 Operation

5.3 System Status Messages

A status message may be an operational or fault message indicating the

inverter/charger’s current operating status. This section will cover the

inverter/charger’s operating and fault modes, and the available status

messages under each mode. Use these status messages and the Status

LED’s to determine the inverter/charger’s current operating status, and to

help troubleshoot the system if a fault occurs.
The System screen displays inverter/charger status messages on the top line

and any accessory status messages on the second line (see Figure 5-1.1). The

FAULT LED

ashes to indicate that one of the ports has a fault. To determine

which port has the fault, press the PORT button or rotate the SELECT knob

until the FAULT LED turns solid. The fault now displays on the second line.

The

rst line identi

es if it is an inverter/charger fault or an accessory fault

(see Figure 5-1.2).

Info:

Whenever referencing “inverter/charger” in this section,

please note it is referring to

all

inverter/chargers in the stack,

not

individual inverter/chargers.

FAULT

PWR

CHG

INV

Over Temperature

Gen off

20.0Vdc 0Adc
System Home

System

Screen

System Home

System Info

Blinking

FAULT LED

Accessory Status

(first port )

System Status

FAULT

PWR

CHG

INV

MS4024PAE Inverter

Low Battery

20 .0Vdc 0Adc
P1 INV Home

Solid

FAULT LED

PORT Screen

Device Menu

Heading

Device Connected

Device Status

Device Info

Figure 5-1.1, SYSTEM Screen Status Messages

Figure 5-1.2, PORT Screen Status Messages

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды