Magnum Energy ME-RTR Скачать руководство пользователя страница 20

Страница: 20 / 80

3.0 Setup

01 AC In Control

The

AC In Control

menu has four different conditions in which the

inverter/charger will connect to incoming AC power. Only one condition may

be selected at any one time – multiple conditions can be enabled, but only

one can be active.

Info:

Before the inverter allows the AC input to connect to the

AC source (grid or gen), the incoming AC must be qualified by

the inverter/charger (voltage is below the high AC input require-

ments, above the

VAC Dropout

setting, and between 50 Hz to

70 Hz for domestic models – 40-60 Hz for export models).

Info:

The top status line of the LCD display alternates the

inverter/charger status with a secondary

AC IN status when

AC is present, but is

not

connecting as a result of a selection

made in the SETUP menu.

Auto Connect:

Automatically connects to incoming AC power.

VDC Connect:

Connects to incoming AC when the DC battery voltage

is below the

Set Connect Volts

setting in the

02D AC IN VDC

menu.

Disconnects from incoming AC when the DC battery voltage is above the

Set Disconnect Volts

setting, also in the

02D AC IN VDC

menu.

Info

: See SETUP menu 02D on page 28 for a complete

explanation of the

Set Connect Volts

setting.

Time Connect:

Connects to incoming AC when the time of day is between

the

Set

Connect Time

and

Set

Disconnect Time

settings per the

02C AC

In - Time

menu.

Info

: See SETUP menu 02C on page 27 for a complete

explanation of the

Set Connect Hour/Minute/AM-PM

setting.

AC In - Disabled:

Disconnects incoming AC when selected. This setting

will prevent incoming AC from connecting to the inverter/charger.

Example:

AC is present, but

Time Connect

has been selected from the

01 AC In Control

menu, and the current time of day is 6PM. The

02C AC

In-Time

menu’s current setting is 2AM - 8AM. The current time of 6PM is

outside the connect time, so the inverter/charger will not connect to the

incoming AC until after 2AM. The primary

status will display “

Inverting

”

and the secondary

status will display “

Time Connect

” to let you know the

reason that incoming AC has not connected.

•
•

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Бренды по названию

Популярные бренды