Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 24 / 80

3.0 Setup

01 DC Meters

01A DC Volts:

DC Volts

provides the battery voltage. The

DC Volts

display provides the voltage from the battery bank connected to the

inverter. Accuracy is ±1.5% with a 0.1 VDC resolution.

01B DC Amps:

While inverting, the

DC Amps

reading displays a negative

number to show the battery current used by the inverter. If in Charge

mode, this setting displays a positive number to show the amount of

current delivered to the batteries. The accuracy of this display below 1

amp AC (~10 amps DC @ 12VDC) is not detected. When the current in

or out of the batteries is greater than 1 amp AC, the display accuracy

is ±20%.

01C Charge Time:

This meter displays whenever the charger is in the

Bulk or Absorb mode. The meter does not accumulate time when in

Float, Charger Standby, Full, or Silent mode.

Info:

Once the charger leaves the Absorption mode and

enters the

nal charge stage, this timer is reset and will not

accumulate until the charger reenters the Bulk or Absorption

charge mode.

02 AC Meters

02A Output Volts:

This menu provides the AC voltage measurement at

the inverter’s output terminals. If inverting, this measures the inverter’s

output voltage. If in Charge mode, this measures the AC voltage that is

passing through the inverter from the source (e.g., grid or generator).

02B Output Hz:

While inverting, this menu displays the output frequency

of the inverter. When the incoming AC source is connected to an inverter,

this meter displays the frequency of the incoming AC source (i.e. grid or

generator) that is passing through the inverter to the inverter’s output

terminals. The frequency is shown in Hertz (Hz).

02C Load Amps:

This menu displays the load the inverter is running in

AC amps – measured at the inverter’s output terminals. This number is

always displayed as a positive number.

02D Input Amps:

This menu displays the total AC amps being used by

the inverter for charging, and any connected load at the output of the

inverter.

Example:

If the charger is using 20A from the AC source and the load

connected to the inverter output is using 10A, the combined load on the

incoming AC source is 30A. So,

30A

would be displayed as the input amps.

02E Inv/Chg Amps:

While charging, this menu displays the amps the

charger is using from the AC source. When inverting, this menu displays

the current of the load the inverter is powering.

Info:

The

02E Inv/Chg Amps

value is determined by subtracting

the

02C Load Amps

value from the

02D AC Input Amps

value.

•

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды