Magnum Energy ME-RTR Скачать руководство пользователя

Страница: 6 / 80

1.0 Overview

The ME-RTR, or “router” hereafter, has many of the same features as the

ME-ARC50 advanced remote with the added functionality required to paral-

lel Magnum MS-PAE inverter/chargers. The router is designed to easily and

quickly connect the MS-PAE series inverter/charger in parallel without the

need to program each inverter. The router will accommodate up to four MS-

PAE inverter/chargers in parallel plus accessories.

The ME-RTR is equipped with the following features:

LED Indicators

The at-a-glance LEDs provide the inverter/charger,

router, communication ports, and auxiliary relay statuses in a

straightforward way.

LCD Display

The LCD display is a 20 x 4 line (80 characters total)

alphanumeric display used for setting up the inverter/charger operation,

as well as viewing current status or fault messages.

ON/OFF Pushbuttons (x2)

Allows all the inverters or chargers to be

quickly enabled or disabled.

Info:

The router’s ON/OFF INVERTER and ON/OFF CHARGER

buttons function normally when a ME-ARC is connected

through a router in a parallel system.

PORT Button

This button scrolls through the six communication and

accessory ports and displays information.

CTRL Button

This button is used to select inverter, charger, and AGS

functions previously set up using the SETUP button.

METER Button

This button is used to access the ‘read only’ meters for

DC, AC, AGS, and BMK.

SETUP Button

This button is used to access the setup menus for the

inverter, charger, AGS, and BMK. The SETUP button may be password

protected to keep unauthorized users from accessing the SETUP

menus.

•

Inverting

25.6 VDC 20 Amps

System Home

PORT, CTRL, METER, SETUP,

TECH Buttons

Rotary

SELECT Knob

LCD Display

LED

ON/OFF

LED Indicators

Figure 1-1, Front Panel Features

Содержание ME-RTR

















































































Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды

Magnum Energy ME-RTR, Руководство пользователя

Результаты поиска

Содержание ME-RTR

Отзывы:

Похожие инструкции для ME-RTR

Бренды по названию

Популярные бренды