LNS GT 326-E Скачать руководство пользователя страница 89

Страница: 89 / 218

8 - 12

Chapter 8 OPERATION

GT 326-E

PART SETUP

The maximum/minimum acceptable feeding length for

machining a part.

TOO SHORT

The minimum allowable bar feeding distance.

TOO LONG

–COLLET CLOSED

The maximum allowable feeding distance when chuck is

closed.

TOO LONG

–COLLET OPEN

The maximum allowable bar feeding distance when

chuck is open.

The setup varies depend on lathe type.

Lathe type

Fixed type

Swiss type

Too short

Part length -15mm

Too long collet
closed

Less than part
length

(Max spindle
movement of
machining a
part)+15mm

Too long collet
open

Part length
+15mm

Less than part
length

FEEDING TYPE

Defines if the lathe turret waits in position or follows the

barstock displacement during feeding operation.

TURRET PARKED IN POSITION

Turret moves forward for a part length and waits till

barstock touches it.

TURRET MOVES TO POSITION

Turret moves backward to touch the front tip of barstock

and follows it to the part length position.

APPLICATION

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 89 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: