LNS GT 326-E Скачать руководство пользователя страница 129

Страница: 129 / 218

9 - 14

9 TROUBLESHOOTING GUIDE

GT 326-E

3. Check if the bar measuring device is functioning

properly.

4. Press

“STOP” button on HMI to clear the alarm.

Note: If TOP CUT is positioned without turret stopper
change

“TOP CUT” setup.

AL26 Bar Feeder Not In AUTO Mode!

Description

To remind the operator that the lathe is possibly in

AUTOMATIC mode but the bar feeder is still in MANUAL

mode.

The bar feeder is in MANUAL mode when the lathe

chuck is opened and closed 3 times without starting the

bar feeder in Automatic mode.

Troubleshooting

Switch the bar feeder to AUTOMATIC mode.

AL35 Bar Stock Moving Forward While Chuck Closed!

Description

During chuck close, bar feeder keeps reading the

position of pusher. If the distance of pusher moving

forwards is larger than

“PART FEEDING: Too long collet

closed

”

setup, the alarm will arise.

Troubleshooting

1. Check if the bar stock is separated from the pusher

collet or if the collet is broken

2. Check if

“PART FEEDING” setup is correct

3. Check if the feeding mechanism is malfunction or if

the chain is broken.

4. Check if the lathe chuck is malfunctioning or the

clamping force setup is incorrect.

5. Press

“STOP” button on HMI to clear the alarm.

AL36 NC Alarm!

Description

Barfeed receives the alarm message from lathe during

Auto mode.

Troubleshooting

Please check the following setting and signal.
1.  INTERFACE45: A2 signal logic setup.
2.  INTERFACE49: A2 signal definition.
3.  Interface cable A2

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 129 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: