LNS GT 326-E Скачать руководство пользователя страница 76

Страница: 76 / 218

Chapter 7 GENERAL DESCRIPTION

7 - 23

GT 326-E

7.14 BAR PREPARATION

Bar preparation is the machining process which changes the shape of bar tip. It aims to get an

improved insertion process during automatic process. The bar preparation must be selected

according to the finger component the user chose. We recommend customers proceed bar

preparation in advance for best machining performance.

Chamfering

The very basic and necessary preparation. It’s strongly

recommended to apply this machining on each bar stock

when a finger chuck is selected.

Turning down

Due to strength concern, the maximum collet size within

a guiding channel range is limited by its own wall

thickness and therefore the maximum bar diameter is

limited. To maximize the bar stock diameter, the user is

recommended to turn down the bar tip as shown. The

maximum bar stock diameter should be kept 1mm below

the guiding channel.

Bar Preparation for pusher with cone head.

When the optional remnant disposal is selected to push

the remnant through the chuck of the lathe by the newly

loaded bar instead of being retracted in the bar feeder a

cone must be installed on the pusher instead of a collet.

For safety and performance reasons the bar end must

be chamfered at a 60 degree angle.

Please contact our office for further details.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 76 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: