LNS GT 326-E Скачать руководство пользователя страница 85

Страница: 85 / 218

8 - 8

Chapter 8 OPERATION

GT 326-E

Press

and

to switch bar feeder

AUTOMATIC

mode. Then switch the

lathe to

AUTOMATIC

mode.

Method B:

If parameter

”Top cut positioning”=With turret, never switch the bar feeder into

AUTOMATIC mode if the chuck of the lathe is open but no stopper in front of

the chuck.

Do not switch lathe to AUTO mode before bar feeder is in AUTO mode.

8.3.2 Continue an interrupted machining

Conditions below must be fulfilled :

1. The lathe is not in AUTOMATIC mode.

2. The chuck of the lathe is open.

3. The bar stopper in lathe is positioned at part length position.

4. The bar feeder guiding channel is closed and the pusher is not at home

position.

Step

Description

Manually advance the pusher until the bar is against the bar stopper in the lathe.

Close the chuck of the lathe.

Press

and then

to switch the bar feeder to

AUTOMATIC

mode. Then

switch the lathe to

AUTOMATIC

mode.

If “Top cut positioning”=Without turret, never switch the bar feeder into

AUTOMATIC mode if the chuck of the lathe is open with no bar stopper in

front of the face of the chuck of the lathe to receive the front of the bar.

2. Never switch the lathe into AUTOMATIC mode before switching the bar

feeder into AUTOMATIC mode.

8.3.3 Switch the bar feeder and lathe from Automatic to Manual mode

When the lathe finishes a machining cycle and the last part is cut-off with chuck closed, switch

the bar feeder and the lathe to manual mode as follows:

Step

Description

Switch the bar feeder to manual mode first.

Switch the lathe to manual mode and open the chuck of lathe last.

Never open the chuck of the lathe when the lathe is in manual mode and the

bar feeder is in AUTOMATIC mode.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 85 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: