LNS GT 326-E Скачать руководство пользователя страница 55

Страница: 55 / 218

7 - 2

Ch 7 GENERAL DESCRIPTION

GT 326-E

7.1.2

Bar loading adjustment

Reading the scale next to the bar diameter bar selection adjusting handle select the diameter

range that fits the bar to load.

Range A: 3 to 4mm

Range B: 4 to 7mm

Range C: 7 to12mm

Range D: 12 to 21mm

Range E: 21mm and above

Procedure:

1. Loosen the locking handles (A) and raise the upper limiters (B)

2. Release the locking handle (D), slide the diameter adjusting handle (E) to the desired

position and secure with locking handle. The loading fingers will be positioned properly.

MAGAZINE UPPER LIMITERS

Adjustment

1. Place a few bars of the desired diameter on the inclined surface (C), resting on the

adjustable end stops (F).

2. Lower the upper limiters (B) to obtain a clearance of around 1mm with the bars positioned

on the inclined surface.

3. Tighten the locking handles (A).

Round bar

Hex bar

Square bar

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 55 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: