LNS GT 326-E Скачать руководство пользователя страница 117

Страница: 117 / 218

9 - 2

9 TROUBLESHOOTING GUIDE

GT 326-E

Description

Bar feeder is unable to start in AUTO mode when the

lathe chuck is open.

Troubleshooting

1. Close the lathe chuck.

2. Check if INTERFACE00 setup corresponds to lathe

chuck signal.

Description

Bar feeder detects the lathe door is open. Once receiving

the signal the servo motor will stop operating.

Troubleshooting

Close the lathe door.

Description

When the bar feeder is in manual mode, main cover is

open and the guiding channel is closed.

Troubleshooting

Manually close main access cover.

Description

Bar feeder unable to start in AUTO mode when the guiding

channel is open and the lathe chuck is closed.

Troubleshooting

1. Open the lathe chuck.

2. Check if

“INTERFACE00” setup corresponds to chuck

signal.

Description

The bar measuring device (front stopper) is not ready when

AUTO + START

is pressed this message will be

displayed.

Troubleshooting

Press channel open

to clear this message.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 117 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: