LNS GT 326-E Скачать руководство пользователя страница 67

Страница: 67 / 218

7 - 14

Ch 7 GENERAL DESCRIPTION

GT 326-E

7.8 HEADSTOCK SYNCHRONIZATION DEVICE

Note:

This device is required when the bar feeder is installed on

sliding headstock

(Swiss

style) only. Its purpose is to detect any movement of the headstock and to prevent small diameter

bars to buckle, bend or disconnect from the collet of pusher while the headstock is moving back

and forth.

The synchronization device is mechanically connected to the machine headstock and has a

built-in sensor to reading the movement of the sliding headstock. The pusher/bar stock

movement is synchronized with the headstock movements during automatic mode.

During automatic mode, there are 2 conditions for the feeding system:

Headstock Synchronization:

When the collet of the lathe is closed the feeding system (pusher/bar stock) movement is

synchronized with the headstock movements. When the collet is open the synchronization

system is disabled while the servo drive maintains a reduced torque to keep the bar in contact

with the cut-off tool and preventing short parts. This mode applies to Swiss type lathes only.

*The location of the synchronization device will depend on the type of lathe. It can be installed

either in the front or in the rear of the bar feeder.

Synchronization device*

(rear mounting)

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 67 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: