LNS GT 326-E Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 218

LNS GT 326-E Скачать руководство пользователя страница 8

Chapter 2 TECHNICAL DATA

2 - 1

GT 326-E

2 TECHNICAL DATA

2.1 CHARACTERISTICS

Model, M

2.5 / 3.2 / 3.7

(12’) / 4.0

Bar diameter range, mm

3 ~ 20 (26 with bar prep.)

Magazine capacity, mm

270

Machine weight, kg

517 / 535 / 549 / 572

Overall length, mm

3365 / 3955 / 4515 / 4955

Overall width, mm

513

Maximum bar length, mm

2640 / 3230 / 3790 / 4230

Hydraulic oil volume

ISO 100 / 28 liters

Air pressure

5~7 bar (90~100 PSI)

Power supply

3X220V, 50/60Hz/5Amp

(Other voltages available)

2.2 CAPACITY (DIAMETER)

2.2.1 Barstock Straightness Specifications and Performance

For optimum rotational performance speeds, bar stock straightness needs to be .020” per side,
per  3.25  feet,  non  accumulative.  Bar  stock  out  of  this  tolerance  will  not  run  at  optimum  RPM.
Other  factors  such  as  material  type  (brass,  copper,  bronze  and  other  malleable  materials),
clamping  efficiency  of  the  machine  workholding,  and  alignment  of  the  bar  feed,  oil  type,  bar
preparation and spindle liners will affect optimum RPM capability of the system.

Spindle Bore

Dia.

Guiding

Channel

Bar stock Dia.

Range without Bar

Preparation

Bar stock Dia. Range

with Bar Preparation

8

8

(3) ~ 5

(5) ~ 7

11

11

(3) ~ 8

(8) ~ 10

14

14

(4) ~ 10

(10) ~ 12

17

17

(7) ~ 14

(14) ~ 16

19

19

(9) ~ 16

(16) ~ 18

21

21

(11) ~ 18

(18) ~ 20

23

23

(13) ~ 20

(20) ~ 22

27

27

(17) ~ 23

(23) ~ 25

Unit : mm

GT 326-E is available for loading bar stock diameter from 3 to 20 mm
(26 mm with bar prep.).

However, for optimum machining performance, the gap between bar
stock and the guiding channel should be kept around 1mm. The bigger
the gap the more chances of vibrations especially with bent bar stock.
Each guiding channel has a range of 10mm above the bar diameter.

Channel

size

«
...
6
7
8
9
10
...
»

Содержание GT 326-E



























































































































































































































Отзывы:

Нет отзывов