manualshive.com logo in svg

LNS GT 326-E, Инструкция по эксплуатации, Страница: 121 / 218

Поделиться
Скачать
LNS GT 326-E Скачать руководство пользователя страница 121

9 - 6

 

9 TROUBLESHOOTING GUIDE 

 

GT 326-E 

 

 

AL02 Main Access Cover Open! 

Description 

This alarm only applies when the main access cover 
safety switch SQ11 is installed. 
When the guiding channel is open and the main access 
cover is opened the CE safety switch SQ11 is 
disengaged. This alarm will be displayed. 

 

Troubleshooting 

1.  Close the main access cover.   
2.  If the cover is already closed:   

(1)  Check if there is something blocking the cover 

or if the cover is bent to prevent the sensor 
SQ11 to operate. 

(2)  Check if the switch SQ11 is defective.   
(3)  Press 

“STOP” key on HMI to clear the alarm. 

 

AL03 Bar Feeder Retracted Or Not In Working Position 

Description 

Following the operation procedures described on 7.12.2, 
when the bar feeder is retracted and both of the retraction 
safety switches 

“SQ10” and “SQ10a” are engaged, the 

alarm message will be generated. 
 

＊

 

This alarm only applies to bar feeder with optional 
Z-axis retraction.

 

 

Troubleshooting 

1.  Position the bar feeder in its working position. 
2.  Check if the safety switches are defective or 

misadjusted. 

3.  Press the STOP button on the remote control to 

reset the alarm. 

 

AL04 Oil Pressure Failure! 

Description 

When oil pump is operating but switch SP2 doesn

’t 

detect any oil pressure in 60 seconds (SP2 OFF). This 
alarm only shown after the lathe finishes machining a 
workpiece and chuck is open.   
This switch is optional so this error message is only 
available when bar feeder installed this switch. 

 

Troubleshooting 

1. Check if oil bump can supply oil smoothly. 
2. Replace oil pressure switch SP2 if 

it’s broken.   

3. Press 

“STOP” button on remote control to remove. 

 

 

Содержание GT 326-E



























































































































































































































Отзывы:

Нет отзывов