LNS GT 326-E Скачать руководство пользователя страница 77

Страница: 77 / 218

7 - 24

Ch 7 GENERAL DESCRIPTION

GT 326-E

7.15 SPINDLE REDUCTION TUBES

The efficiency of the bar guiding while in rotation in the lathe is determined by the clearance

between the spindle reduction tube and the rotating bar. The greater the clearance is, the more

frequent the vibrations are.

Using reduction tubes helps to decrease this clearance. Guiding is thus improved, but, in

addition, the insertion of the bar into the clamping device of the lathe is made much easier. The

inside diameter of the reduction tubes should be chosen in terms of the diameter of the bar

(diameter of the bar + 1 mm), but should always be larger than that of the diameter of the feeding

pusher.

For inserting and removing the spindle reductions, move the bar feed system using the retraction

device (Chapter 7/ Point 8) or slide the spindle liner through the bar feeder if design permits.

Spindle reduction tubes are available upon request.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 77 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: