LNS GT 326-E Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 218

LNS GT 326-E Скачать руководство пользователя страница 40

Chapter 4 ELECTRICS

4 - 19

GT 326-E

PCB

4.7 SAFETY SWITCHES

The safety switches are used as reminders for user during operation and for safety reasons.
They will impede any handling as long as the bar feeder is not in operational position.

Jumper on TB8 is removed when safety
switches are wired.



Main access cover safety switch (SQ11)

The switch detects whether the main cover is closed or
open. If the main access cover open the bar feeder will
not start in AUTO mode.

When the cover is open, a signal will be sent to PLC
input contact X20. An alarm message

“Main cover is

open” is displayed.

Please refer to 4.4 and 4.5 for wiring connection in the
switch.



Optional Retraction safety switches (SQ10)
(SQ10a)

The switches detect the position of bar feeder to ensure
bar feeder is ready and the lathe can be put in
production.

When bar feeder is ready, the safety switches SQ10 and
SQ10a will operate as the figure A and figure B.

Following the procedures on 7.12.2, when bar feeder is
moved, the safety switches SQ10 and SQ10a will
operate as the figure C. A signal will be sent to PLC
contact X21 and an alarm message “AL03” is displayed
reminding the operator to move back bar feeder in the
working position before starting the lathe in production.

Please refer to 4.4 and 4.5 for wire connection in the
switch.

SQ10&SQ10a

SQ11

Fig. A

SQ10

SQ10a

SQ10

SQ10a

Fig. B

Fig. C

SQ10

SQ10a

1-position

1-position

Alarm

2-position

«
...
38
39
40
41
42
...
»

Содержание GT 326-E



























































































































































































































Отзывы:

Нет отзывов