manualshive.com logo in svg

LNS GT 326-E, Инструкция по эксплуатации, Страница: 101 / 218

Поделиться
Скачать
LNS GT 326-E Скачать руководство пользователя страница 101

8 - 24

 

Chapter  8  OPERATION 

 

GT 326-E 

 

 

 

 

OPTIONS SETUP 

HEADSTOCK SYNCHRONIZATION DEVICE 

Defines if using the headstock synchronization device. 

EXTERNAL STABILIZER OPERATION 

Defines the action of optional external stabilizer before 
the pusher reaches the position set on second 
anti-vibration. 
-  Keep closed 
-  Follow the chuck moving open and close 

 

 

OPTIONS SETUP

 

TOP CUT POSITIONING 

Defines Top Cut positioning with or without turret help. 

BAR INSERTION CHECK 

When bar insertion is completed the pusher will move 

back and forth. During this cycle the vise with close to 

verify if the bar is inserted. 

 

 

 
 

INTERFACE 

Shows several interface parameter status. Please refer 

to the INTERFACE PARAMETER NUMBERS 

description as following or click on the parameter 

number on the touch screen to show more information. 

 

 

00- Clamping signal (A1) logic setup 

1  Clamping signal on HMI (A1) lit, the lathe chuck is 

closed. 

2  Clamping signal on HMI (A1) lit, the lathe chuck is 

open.

 

 

 

 

 

 

 

OPTIONS 

INTERFACE 

Содержание GT 326-E



























































































































































































































Отзывы:

Нет отзывов