LNS GT 326-E Скачать руководство пользователя страница 120

Страница: 120 / 218

9 TROUBLESHOOTING GUIDE

9 - 5

GT 326-E

9.3 ERROR MESSAGE DESCRIPTION AND TROUBLESHOOTING

GUIDE

When an error occurs the corresponding alarm message will be displayed on the HMI screen.

Follow the troubleshooting instructions below to solve the problems and clear the alarms.

To clear the alarm after troubleshooting presses STOP.

If the alarm message remains active please contact LNS or one of its representatives for further

technical assistance.

AL01 Emergency Stop Line Is Open!

Description

The emergency stop circuit includes:



Emergency stop button on HMI (STP1)



Emergency stop circuit of the lathe



Main circuit-breaker QM1



Contactor K1

During normal operation the contactor K1 is energized

and continuously sending signal to PLC input X10.

Whenever this circuit is open K1 will de-energize and the

signal to PLC input contact X10 is OFF

Sequence of actions:

1. The 220V AC to the servo amplifier is interrupted.

2. All PLC output signals are interrupted except for Y20

(input signal of alarm relay R1).

3. The alarm AL01 is displayed on the HMI screen.

If the relay K8 (DCS relay) is installed press MANUAL

button on the HMI after powering up the bar feeder

otherwise this error message will be displayed.

Troubleshooting

1. Check if the emergency stop on HMI (STP1) is pressed. If yes release it.

2. Check if the emergency stop circuit on the lathe is open. If yes clear all lathe alarms.

3. Check if circuit-breaker (QM1) has tripped. If yes reset it.

4. Check if A1 and A2 of contactor (K1) have 24 VDC.

5. Press

“STOP” button on HMI to clear the alarm.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 120 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: