LNS GT 326-E Скачать руководство пользователя страница 79

Страница: 79 / 218

8 - 2

Chapter 8 OPERATION

GT 326-E

Auto ready/ Auto start

To switch the bar feeder to

AUTOMATIC

mode, press "Auto

ready

(PLC X31)" then "Auto start

(PLC X32)" key

for 3 seconds, both LED in the keys are ON if all conditions are

met. The bar feeder is now in

AUTOMATIC

mode.

To switch to

AUTOMATIC

mode, one of the following conditions

must be fulfilled :

•

Main guiding channel closed.

- OR -

•

Main guiding channel open and the pusher is at home

position (SQ2 ON) and the bar measurement device is

ready.

Manual

This key offers two functions :

•

To switch the bar feeder to

MANUAL

mode. When the

bar feeder is in

MANUAL

mode, the LED in the key is

ON and the user can operate the bar feeder by function

keys.

•

To reset the bar feeder from an emergency stop alarm.

Rightward

Move pusher rightward. Only available when the bar feeder is

MANUAL

mode.

Slow Rightward

Press

then press

Move the pusher rightward with 2% of the general speed. Only

available when the bar feeder is in

MANUAL

mode.

Leftward

Move the pusher leftward. Only available when bar feeder is in

MANUAL

mode.

Slow Leftward

Press

then press

Move the pusher leftward with 2% of the general speed. Only

available when the bar feeder is in

MANUAL

mode.

Open Guiding Channel

This key offers three functions :

1. When the pusher is at home position and the bar feeder is

MANUAL

mode

pressing this key twill automatically

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 79 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: