LNS GT 326-E Скачать руководство пользователя страница 62

Страница: 62 / 218

Chapter 7 GENERAL DESCRIPTION

7 - 9

GT 326-E

7.4 DIAMETER CHANGEOVER

The channel set is composed of the guiding channel set (chapter 7.2) and feeding system

(chapter 7.3). Once the bar stock diameter is out of the guiding channel range a complete

changeover is required that includes the guiding channel set, the pusher assembly and hooks as

well as the front rest adjustment.

7.4.1

Layout of the elements

7.4.2

Complete Changeover

Please do not turn the power off of the bar feeder during a changeover to ensure the

pusher position is read correctly and make sure there is no bar stock in the collet or

inside the guiding channels.

1. Press

to switch bar feeder into manual mode

2. Press

to close channel and press

to advance the pusher through the vise.

3. Press

to open the guiding channel.

4. Press

Emergency Stop button to disable all functions and movements of the bar

feeder.

5. Take out pusher, loading flag and remove pusher hooks.

Release hooks

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 62 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: