LNS GT 326-E Скачать руководство пользователя страница 134

Страница: 134 / 218

9 TROUBLESHOOTING GUIDE

9 - 19

GT 326-E

AL003

Under voltage

Clearing Method

This fault message can be removed automatically after the voltage has

returned within its specification.

Potential Cause

Checking Method

Corrective Actions

The main circuit

voltage is below its

minimum specified

value.

Check whether the wiring of main

circuit input voltage is normal.

Reconfirm voltage wiring.

No input voltage at

main circuit.

Use voltmeter to check whether

input voltage at main circuit is

normal.

Reconfirm power switch.

Input power error

(Incorrect power

input)

Use voltmeter to check whether the

input voltage is within the specified limit.

Use correct power supply or

serial stabilizing power.

AL004

Motor error

Clearing Method

Turn OFF the power supply and restart the servo drive.

Potential Cause

Checking Method

Corrective Actions

Encoder is damage. Check Encoder for the damage.

Repair or replace the motor.

Encoder is loose.

Examine the Encoder connector.

Install the motor again.

The type of the

servo motor is

incorrect.

Check if the servo drive and servo

motor are not correctly matched for size

power rating.

Replace the motor.

AL005

Regeneration error

Clearing Method

Turn OFF the power supply and restart the servo drive.

Potential Cause

Checking Method

Corrective Actions

Regenerative

resistor is not

connected.

Check the wiring connection

of regenerative resistor.

Reconnect regenerative

resistor.

Regenerative

switch transistor

fault

Check if regenerative switch transistor

is short-circuited.

Please contact your distributor for

assistance or contact with Delta.

Parameter setting

is in error

Confirm the parameter setting and

specifications of regenerative

resistor.

Correctly reset parameter

again.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 134 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: