LNS GT 326-E Скачать руководство пользователя страница 116

Страница: 116 / 218

9 TROUBLESHOOTING GUIDE

9 - 1

GT 326-E

9 TROUBLESHOOTING GUIDE

This chapter lists all the error messages, their description and a brief troubleshooting. The error

messages aim to remind the operator that an abnormal situation is taking place or has happened.

Whenever an error message is activated please follow the description and troubleshooting to

check the problem. If necessary contact us or one of our representatives for technical support.

9.1 WARNING MESSAGES

Warning messages are designed to remind users of the bar feeder status. Under the following

conditions there will be a warning message but the alarm signal output (Y04, R1) of the bar

feeder will not send am alarm signal to the lathe. Please follow the help instructions guide to

clear the warning messages.

Warning messages

Description

Pusher is at the wrong position.

Troubleshooting

Manually return pusher to its home position.

Description

The remnant is too long or barstock is between the lathe

and the bar feeder.

Troubleshooting

Manually remove the remnant.

Description

Lathe chuck is closed, press

is invalid.

Troubleshooting

1. Open lathe chuck.

2. Check INTERFACE00 setup related to lathe chuck

signal.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 116 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: