LNS GT 326-E Скачать руководство пользователя страница 104

Страница: 104 / 218

Chapter 8 OPERATION

8 - 27

GT 326-E

11- PUSH signal (A4) setup

Defines the type of the A4 signal for bar feeding.

A4 signal is a latched signal. The pusher will

advance the bar stock while receiving A4 signal.

A4 signal is a pulsed signal. The pusher will

advance the bar stock once A4 signal is sent

12- Pushing force setup with sliding headstock

Defines the pushing force for sliding lathe with chuck

opened.

When the lathe chuck opens, the pushing force is
according to “PUSHER TORQUE RATE”: TO

COMPENSATE THE PUSHER FRICTION.

When the lathe chuck opens, the pushing force is

according to

“PUSHER TORQUE RATE”: AGAINST

THE CUT-OFF TOOL.

13- R2 while in production cycle (Refer to INTERFACE14, 15, 16 for related setup)

Defines if R2 signal is On or Off during production cycle

R2 signal output according to INTERFACE14, 15,

16 and 34 setup.

R2 signal is ON after the newly loaded bar reaches

the Top Cut position and turns OFF when bar feeder
starts a new loading cycle.
This output indicates the bar feeder is in working
mode.

＊

Refer to the timing chart <3> on 8.6.2.1

14 R2 during End of Bar (Refer to INTERFACE13, 15, 16 for related setup)

Defines the condition of R2 signal at End of Bar.

R2 signal will be OFF during End of Bar condition.

R2 signal will be ON during End of Bar condition.

＊

Refer to the timing chart <3> on 8.6.2.1

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 104 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: