LNS GT 326-E Скачать руководство пользователя страница 58

Страница: 58 / 218

Chapter 7 GENERAL DESCRIPTION

7 - 5

GT 326-E

7.3 PUSHER GUIDING CHANNEL AND PUSHER SUPPORT

The pusher assembly advances the bar into the lathe. It is chain driven and is controlled by servo

motor.

When a new bar is loaded the loading flag (B) advances the bar onto the insertion location

behind the bar clamping device. It then retracts to its home position. The bar is then clamped in

the clamping vise. The long pusher is lowered into the pusher guiding channel. The pusher

advances and the bar is inserted into the collet of the pusher.

The bar is released by the vise and the bar is ready to advance into the lathe for automatic

production after being measured by the bar measuring device in the bar feeder.

7.3.1 Layout of the elements

Designation

Description

Flag

Loading flag

Long pusher

Pusher hook

Rotating sleeve

Collet

Pusher guiding channel

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 58 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: