LNS GT 326-E Скачать руководство пользователя страница 139

Страница: 139 / 218

9 - 24

9 TROUBLESHOOTING GUIDE

GT 326-E

AL018

Encoder output error

Clearing Method

Turn OFF the power supply and restart the servo drive.

Potential Cause

Checking Method

Corrective Actions

Encoder itself or the

wiring of encoder is in

error.

Check if the recent fault records (P4-

00 ~ P4-05) display on the drive

keypad in accordance with the

fault codes AL011, AL024, AL025

and AL026.

Perform the corrective actions as

described in AL011, AL024,

AL025 and AL026.

The output frequency

for pulse output may

exceed the limit of its

allowable setting

value.

Check if the following conditions

occur:

Condition 1: Motor speed is above

the value set by P1-76.

Condition 2:

Correctly set P1-76 andP1-46.

1. Ensure that the motor speed

is below the value set by

P1-76.

AL019

Serial communication error

Clearing Method

Turn OFF the power supply and restart the servo drive.

Potential Cause

Checking Method

Corrective Actions

Communication

parameter setting

is defective.

Check the communication parameter

setting.

Correctly set parameter

setting.

Communication

address is

incorrect.

Check the communication address.

Correctly set communication

address.

Communication value

is incorrect.

Check the communication value.

Correctly set communication

value.

AL020

Serial communication time out

Clearing Method

Turn OFF the power supply and restart the servo drive.

Potential Cause

Checking Method

Corrective Actions

Setting value in

time out parameter

is not correct.

Check communication time

out parameter setting.

Correctly set P3-07.

Not receiving

communication

command for a long

time.

Check whether communication cable

is loose or broken.

Tighten the communication cable,

make sure the communication

cable is not damaged and ensure

all wiring is correct.

Содержание GT 326-E



























































































































































































































Результаты поиска

Содержание GT 326-E

Отзывы:

LNS GT 326-E, Инструкция по эксплуатации, Страница: 139 / 218

Результаты поиска

Содержание GT 326-E

Отзывы: